YASKAWA Varispeed-606PC3 User Manual

1 .
VS-606PO3
INVERTER MAIN UNIT
(Cont'd)
t The
values show a short-term average
deceleration torque when the motor
single-unit
decelerates
from 60 Hz at the shortest distance

It is not a continuous regenerative
torque .
Average
deceleration torque is changed
by the motor loss,

If the motor
operates
exceeding
the base frequency, this value is reduced

When a
large
regenerative
torque is
needed, use an optional
braking resistor .
t To select
"automatic restart after momentary
power loss," set the 1st digit of constant (No
46) to "1 "
Automatic restart
is available for up to 1 second for models
CIMR-PCU20P7 or less or up to 2
seconds for models CIMR-PCU21
P5 or greater
#
Temperature during shipping (for short period)
Voltage
Class 2 30 V
3-phase
InverterInverter Model
-PCU
20P 1 20P2 20P4 20P7
21P5 22PO 22P2 23P7
Operation Signal
_ Forward run/reverse run
by separate commands
Fault Reset Releases protectior while the function is operating
Multifunction
contact input 3 of the following signals available
a
Multifunction
to select .
- Input Selection
External
fault,
3-wire' .
muiispeed command, jog operation,
accel/decel
time select,
sequence, external baseblock, speed search
command
Photo-
Multifunction contact output - two of the following
signals
coupler
available to
select
(48
VDC, 50 mA or less)
cn
o
C
Opera-
Output
(During running output, zero
speed, frequency agreement ,
output frequency ? set value, during overtorque
detection, etc )
tion
C
CL
State
Possible to select these functions as multifunction
outputs
o
Contact
1 NO/NC contact
output (250 VAC 1 A, 30 VDC 1 A or less)
o Output
(During running output, zero
speed, frequency agreement ,
12
output
frequency
z
set value, during overtorque
detection,
et c )
o
The following setting-up
is available . frequency reference
bias/gain, upper/lower frequency limit . DC injection
braking
Built-in
Function
current/time at starting/stopping,
full-automatic torque boost,
frequency meter calibrating gain,
fault
retry,
prohibited
frequency, S-curve accel/decel .
>11
LED Status
Displays contents at RUN/ STOP
and protective function
Display
operation .
Digital Operator
Displays set frequency,
output frequency, output current,
o ° direction of rotat ;on, and the fault
status .
o Analog Output
Analog output (0
to
10
VDC) Possible to select output
'- Monitor
frequency or output current
Protective Configuration
Enclosed wall-mounted type (NEMA 1), water and
dust tight
type (NEMA4)
Cooling Method
NEW 1
Serf-cooling
Forced-cooling
NEMA4
Self-cooling
Forced
cooling
- Forced-cooling
Mass
Ib
(kg)
NEMA4
440
66(3) 88 (4) - 8 .8 (4) 132
(6)
Ambient Temperature +14 to 104°F (--10 to
+409C) (not
frozen)
E
o
Storage Temperature #
-4
to 140°F (-20 to +60°C)
o
~
Humidity
9096 RH
or less(non-condensing)
5 ; c
w
v Vibration
Up to 9 8 m/s 2 (1
G) at less than 20 Hz, Up to 2 m/s
2 (0 2 G)
at 20 to 50 Hz

YASKAWA Varispeed-606PC3 Specifications

General

Brand	YASKAWA
Model	Varispeed-606PC3
Category	Inverter
Language	English