YOKOGAWA DL9040

5-76
IM 701310-17E
:CURSor:MARKer:CM<x>:T:STATe
Function Turns ON/OFF the time measurement of the maker
cursor or queries the current setting.
Syntax
:CURSor:MARKer:CM<x>:T:STATe
{<Boolean>}
:CURSor:MARKer:CM<x>:T:STATe?
<x> = 1 to 4
Example
:CURSOR:MARKER:CM1:T:STATE ON
:CURSOR:MARKER:CM1:T:STATE? -> :CURSOR:
MARKER:CM1:T:STATE 1
:CURSor:MARKer:CM<x>:T:VALue?
Function Queries the time value at the marker cursor position.
Syntax
:CURSor:MARKer:CM<x>:T:VALue?
<x> = 1 to 4
Example
:CURSOR:MARKER:CM1:T:VALUE? -> :CURSOR:
MARKER:CM1:T:VALUE 0.000E+00
:CURSor:MARKer:CM<x>:TRACe
Function Sets the source trace of the marker cursor or queries
the current setting.
Syntax
:CURSor:MARKer:CM<x>:TRACe {<NRf>|OFF}
:CURSor:MARKer:CM<x>:TRACe?
<x> = 1 to 4
<NRf> = 1 to 8
Example
:CURSOR:MARKER:CM1:TRACE 1
:CURSOR:MARKER:CM1:TRACE? -> :CURSOR:
MARKER:CM1:TRACE 1
:CURSor:MARKer:CM<x>:V?
Function Queries all settings related to the voltage
measurement of the marker cursor.
Syntax
:CURSor:MARKer:CM<x>:V?
<x> = 1 to 4
Example
:CURSOR:MARKER:CM1:V? -> :CURSOR:
MARKER:CM1:V:STATE 1
:CURSor:MARKer:CM<x>:V:STATe
Function Turns ON/OFF the voltage measurement of the
maker cursor or queries the current setting.
Syntax
:CURSor:MARKer:CM<x>:V:STATe
{<Boolean>}
:CURSor:MARKer:CM<x>:V:STATe?
<x> = 1 to 4
Example
:CURSOR:MARKER:CM1:V:STATE ON
:CURSOR:MARKER:CM1:V:STATE? -> :CURSor:
MARKER:CM1:V:STATE 1
:CURSor:MARKer:CM<x>:V:VALue?
Function Queries the voltage value at the marker cursor
position.
Syntax
:CURSor:MARKer:CM<x>:V:VALue?
<x> = 1 to 4
Example
:CURSOR:MARKER:CM1:V:VALUE? -> :CURSOR:
MARKER:CM1:V:VALUE 0.000E+00
:CURSor:MARKer:FORM
Function Sets the marker cursor form or queries the current
setting.
Syntax
: CURSor:MARKer:FORM {LINE|MARK}
: CURSor:MARKer:FORM?
Example
: CURSOR:MARKER:FORM LINE
: CURSOR:MARKER:FORM?
-> : CURSOR:MARKER:FORM LINE
:CURSor:SERial?
Function Queries all settings related to the serial cursors.
Syntax
:CURSor:SERial?
Example
:CURSOR:SERIAL? -> :CURSOR:SERIAL:
SCURSOR1:ACTIVE HIGH;
BCOUNT 8;BITRATE 10.00E+00;
BITORDER MSBFIRST;FORMAT BINARY;
HYSTERESIS 1.000E+00;LEVEL 0.000E+00;
MODE 1;POSITION -4.000E+00;TRACE 1;
TRACK OFF;:CURSOR:SERIAL:SCURSOR2:
ACTIVE HIGH;BCOUNT 8;BITRATE 1.000E+00;
BITORDER MSBFIRST;FORMAT BINARY;
HYSTERESIS 3.000E+00;LEVEL 0.000E+00;
MODE 0;POSITION -4.000E+00;TRACE 2;
TRACK OFF
:CURSor:SERial:SCURsor<x>?
Function Queries all settings related to the serial cursor.
Syntax
:CURSor:SERial:SCURsor<x>?
<x> = 1 or 2
Example
:CURSOR:SERIAL:SCURSOR1? -> :CURSOR:
SERIAL:SCURSOR1:ACTIVE HIGH;
BCOUNT 8;BITRATE 1.25E+06;
BITORDER MSBFIRST;FORMAT BINARY;
HYSTERESIS 300.00E-03;LEVEL 0.000E+00;
MODE 1;POSITION -4.00E+00;TRACE 1;
TRACK OFF
:CURSor:SERial:SCURsor<x>:ACTive
Function Sets the active level of the serial cursor or queries the
current setting.
Syntax
:CURSor:SERial:SCURsor<x>:ACTive {HIGH|
LOW}
:CURSor:SERial:SCURsor<x>:ACTive?
<x> = 1 or 2
Example
:CURSOR:SERIAL:SCURSOR1:ACTIVE HIGH
:CURSOR:SERIAL:SCURSOR1:ACTIVE?
-> :CURSOR:SERIAL:SCURSOR1:ACTIVE HIGH
5.9 CURSor Group