YOKOGAWA DL9040 - Page 223

5-189
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:TRIGger:ENHanced:I2CBus:SBHSmode?
Function Queries all settings related to the start byte and high
speed mode of the I
2
C bus trigger.
Syntax
:TRIGger:ENHanced:I2CBus:SBHSmode?
Example
:TRIGGER:ENHANCED:I2CBUS:SBHSMODE?
-> :TRIGGER:ENHANCED:I2CBUS:SBHSMODE:
TYPE HSMODE
:TRIGger:ENHanced:I2CBus:SBHSmode:TYPE
Function Sets the type of the start byte or high speed mode of
the I
2
C bus trigger or queries the current setting.
Syntax
:TRIGger:ENHanced:I2CBus:SBHSmode:
TYPE {HSMode|SBYTe}
:TRIGger:ENHanced:I2CBus:SBHSmode:TYPE?
Example
:TRIGGER:ENHANCED:I2CBUS:SBHSMODE:
TYPE HSMODE
:TRIGGER:ENHANCED:I2CBUS:SBHSMODE:TYPE?
-> :TRIGGER:ENHANCED:I2CBUS:SBHSMODE:
TYPE HSMODE
:TRIGger:ENHanced:LINBus?
Function Queries all settings related to the LIN bus trigger or
queries the current setting.
Syntax
:TRIGger:ENHanced:LINBus?
Example
:TRIGGER:ENHANCED:LINBUS? -> :TRIGGER:
ENHANCED:LINBUS:BRATE 19200;
SOURCE 1
:TRIGger:ENHanced:LINBus:BRATe
Function Sets the LIN bus signal trigger bitrate (data transfer
rate) or queries the current setting.
Syntax
:TRIGger:ENHanced:LINBus:BRATe {<NRf>|
USER,<NRf>}
:TRIGger:ENHanced:LINBus:BRATe?
<NRf> = 1200, 2400, 4800, 9600, 19200
<NRf> for USER = See the main unit User
’s Manual.
Example
:TRIGGER:ENHANCED:LINBUS:BRATE 19200
:TRIGGER:ENHANCED:LINBUS:BRATE?
-> :TRIGGER:ENHANCED:LINBUS:BRATE 19200
:TRIGger:ENHanced:LINBus:SOURce
Function Sets the LIN bus signal trigger source or queries the
current setting.
Syntax
:TRIGger:ENHanced:LINBus:SOURce {<NRf>}
:TRIGger:ENHanced:LINBus:SOURce?
<NRf> = 1 to 4
Example
:TRIGGER:ENHANCED:LINBUS:SOURCE 1
:TRIGGER:ENHANCED:LINBUS:SOURCE?
-> :TRIGGER:ENHANCED:LINBUS:SOURCE 1
:TRIGger:ENHanced:SPATtern? (Serial
Pattern)
Function Queries all settings related to the serial pattern
trigger.
Syntax
:TRIGger:ENHanced:SPATtern?
Example
:TRIGGER:ENHANCED:SPATTERN?
-> :TRIGGER:ENHANCED:SPATTERN:
BITRATE 1.000E+00;CLOCK:MODE 1;
POLARITY FALL;SOURCE 1;:TRIGGER:
ENHANCED:SPATTERN:CS 1;DATA:
ACTIVE HIGH;SOURCE 1;:TRIGGER:ENHANCED:
SPATTERN:LATCH:SOURCE 1;POLARITY FALL;:
TRIGGER:ENHANCED:SPATTERN:
PATTERN "1100110111101111"
:TRIGger:ENHanced:SPATtern:BITRate
Function Sets the bit rate of the serial pattern trigger or queries
the current setting.
Syntax
:TRIGger:ENHanced:SPATtern:
BITRate {<NRf>}
:TRIGger:ENHanced:SPATtern:BITRate?
<NRf> = 1 to 50M (bps)
Example
:TRIGGER:ENHANCED:SPATTERN:BITRATE 1
:TRIGGER:ENHANCED:SPATTERN:BITRATE?
-> :TRIGGER:ENHANCED:SPATTERN:
BITRATE 1.000E+00
Description This command is valid when :TRIGger:ENHanced:
SPA
Ttern:CLOCk:MODE OFF.
:TRIGger:ENHanced:SPATtern:CLEar
Function Clears the entire pattern of the serial pattern trigger (to
don’t care).
Syntax
:TRIGger:ENHanced:SPATtern:CLEar
Example
:TRIGGER:ENHANCED:SPATTERN:CLEAR
:TRIGger:ENHanced:SPATtern:CLOCk?
Function Queries all settings related to clock of the serial
pattern trigger.
Syntax
:TRIGger:ENHanced:SPATtern:CLOCk?
Example
:TRIGGER:ENHANCED:SPATTERN:CLOCK?
-> :TRIGGER:ENHANCED:SPATTERN:CLOCK:
MODE 1;POLARITY FALL;SOURCE 1
:TRIGger:ENHanced:SPATtern:CLOCk:MODE
Function Enables/Disables the clock of the serial pattern
trigger or queries the current setting.
Syntax
:TRIGger:ENHanced:SPATtern:CLOCk:
MODE {<Boolean>}
:TRIGger:ENHanced:SPATtern:CLOCk:MODE?
Example
:TRIGGER:ENHANCED:SPATTERN:CLOCK:
MODE ON
:TRIGGER:ENHANCED:SPATTERN:CLOCK:MODE?
-> :TRIGGER:ENHANCED:SPATTERN:CLOCK:
MODE 1
5.29 TRIGger Group