5-283
IM 710105-17E
Commands
5
:WPARameter<x>:HISTogram:MEASure:PAR
ameter:<Parameter>:STATe
Function Sets or queries the on/off status of a histogram
parameter for waveform parameter measurement.
Syntax
:WPARameter<x>:HISTogram:MEASure:PARa
meter:<Parameter>:STATe {<Boolean>}
:WPARameter<x>:HISTogram:MEASure:PARa
meter:<Parameter>:STATe?
<x> = 1 or 2 (1 only for 2-channel models)
<Parameter> = {
C1|C2|DC|MAXimum|MEAN|MED
ian|MINimum|PEAK|SD2integ|SD3integ|SD
EViation|SDINteg
}
Example (Below are examples for the maximum value.)
:WPARAMETER1:HISTOGRAM:MEASURE:PARAME
TER1:MAXIMUM:STATE ON
:WPARAMETER1:HISTOGRAM:MEASURE:PARAME
TER1:MAXIMUM:STATE?
-> :WPARAMETER1:HISTOGRAM:MEASURE:PAR
AMETER1:MAXIMUM:STATE 1
:WPARameter<x>:HISTogram:MEASure:PAR
ameter:<Parameter>:VALue?
Function Queries the measured value of a histogram
parameter for waveform parameter measurement.
Syntax
:WPARameter<x>:HISTogram:MEASure:PARa
meter:<Parameter>:VALue?
<x> = 1 or 2 (1 only for 2-channel models)
<Parameter> = {
C1|C2|DC|MAXimum|MEAN|MED
ian|MINimum|PEAK|SD2integ|SD3integ|SD
EViation|SDINteg
}
Example (Below are examples for the maximum value.)
:WPARAMETER1:HISTOGRAM:MEASURE:PARAME
TER:MAXIMUM:VALUE?
-> :WPARAMETER1:HISTOGRAM:MEASURE:PAR
AMETER:MAXIMUM:VALUE 1.000E+00
:WPARameter<x>:HISTogram:MEASure:PAR
ameter:POSition<y>
Function Sets or queries the position of a histogram
parameter for waveform parameter measurement.
Syntax
:WPARameter<x>:HISTogram:MEASure:PARa
meter:POSition<y> {<NRf>}
:WPARameter<x>:HISTogram:MEASure:PARa
meter:POSition<y>?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
<NRf>=−5to5(divisions)
Example
:WPARAMETER1:HISTOGRAM:MEASURE:PARAME
TER1:POSITION 1
:WPARAMETER1:HISTOGRAM:MEASURE:PARAME
TER1:POSITION?
-> :WPARAMETER1:HISTOGRAM:MEASURE:PAR
AMETER1:POSITION 1.000E+00
:WPARameter<x>:ITEM
Function Sets or queries a waveform parameter for
waveform parameter measurement.
Syntax
:WPARameter<x>:ITEM {<NRf>|BIT<x>|
MATH<x>,<Parameter>,{2}}
:WPARameter<x>:ITEM?
<x> of WPARameter<x> = 1 or 2 (1 only for
2-channel models)
<NRf> = 1 to 4 (1 or 2 for 2-channel models)
<x> of BIT<x> = 1 or 2
<x> of MATH<x> = 1 or 2 (1 only for 2-channel
models)
<Parameter> =
{
AMPLitude|
AVERage|AVGFre
q|AVGPeriod|BWIDth|DELay|DT|DUTYcycl
e|ENUMber|FALL|FREQuency|I2T|HIGH|LOW
|MAXimum|MINimum|NOVershoot|NWIDth|P
|PABS|PERiod|PN|PNUMber|POVershoot|PP
|PTOPeak|PWIDth|RISE|RMS|SDEViation|T
Y1Integ|TY2Integ|V1|V2|WH|WHABs|WHN|W
HP|Z}
Example
:WPARAMETER1:ITEM 1,AVERAGE
:WPARAMETER1:ITEM?
-> :WPARAMETER1:ITEM 1,AVERAGE
:WPARameter<x>:MODE
Function Sets or queries the waveform parameter
measurement mode.
Syntax
:WPARameter<x>:MODE {HISTogram|TRENd}
:WPARameter<x>:MODE?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:WPARAMETER1:MODE HISTOGRAM
:WPARAMETER1:MODE?
-> :WPARAMETER1:MODE HISTOGRAM
:WPARameter<x>:TRENd?
Function Queries all trend display settings for waveform
parameter measurement.
Syntax
:WPARameter<x>:TRENd?
<x> = 1 or 2 (1 only for 2-channel models)
:WPARameter<x>:TRENd:ASCale
Function Executes auto scaling of the trend display for
waveform parameter measurement.
Syntax
:WPARameter<x>:TRENd:ASCale
<x> = 1 or 2 (1 only for 2-channel models)
Example
:WPARAMETER1:TREND:ASCALE
5.35 WPARameter Group
To Next Page
Loading...
Need help?
General
