YOKOGAWA DLM2000 Series User Manual (English)

Other manuals for YOKOGAWA DLM2000 Series

Questions and Answers:

H
Holly MasonAug 13, 2025
Why are the measured values not correct on my YOKOGAWA Test Equipment?
- L
  lawrencewyattAug 13, 2025
  If the measured values on your YOKOGAWA Test Equipment DLM2000 are incorrect, several factors could be the cause. First, allow the device to warm up for 30 minutes after powering it on. Second, calibrate the DLM2000. Third, ensure proper phase correction of the probe. Fourth, verify that the probe attenuation is correctly set. Fifth, set the offset voltage to 0 V. If the issue persists after checking these points, calibrate the DLM2000 again; if the measured values are still incorrect after calibration, servicing is required.
A
Amanda PaulAug 17, 2025
What to do if nothing is displayed on my YOKOGAWA DLM2000 Test Equipment?
- D
  Drew BauerAug 17, 2025
  If nothing is displayed on your YOKOGAWA Test Equipment DLM2000, here are a couple of things to try: - First, the backlight might be turned off, press any key. - Second, the screen might be displayed with inappropriate colors, turn the power off, and then turn the power on again while pressing RESET.
C
Crystal AlvarezAug 20, 2025
Why I am unable to configure or control the YOKOGAWA DLM2000 through the communication interface?
- S
  Sergio JacksonAug 21, 2025
  If you are unable to configure or control the YOKOGAWA Test Equipment DLM2000 through the communication interface, it could be due to a mismatch between the DLM2000 address used by the program and the specified address. Ensure that the address used in the program matches the DLM2000 address. Also, ensure that the interface is used in a way that conforms to the specifications.
N
Neil ChristianAug 25, 2025
What to do if I cannot save to the specified storage medium on my YOKOGAWA DLM2000?
- A
  alicia83Aug 25, 2025
  If you cannot save to the specified storage medium on your YOKOGAWA Test Equipment DLM2000, it may be because the storage medium is not formatted. Format the storage medium. Alternatively, there may be no more free space on the storage medium. In this case, delete unneeded files or use another storage medium.
B
barnesjoeAug 28, 2025
Why is the display odd on my YOKOGAWA DLM2000?
- J
  jodikellyAug 28, 2025
  If the display on your YOKOGAWA Test Equipment DLM2000 appears odd, it could indicate that the system is not operating correctly. Try turning off the DLM2000 and then turning it back on.
R
Robert JonesSep 1, 2025
How to fix a YOKOGAWA Test Equipment DLM2000 that does not power on?
- J
  Jennifer SantiagoSep 1, 2025
  If your YOKOGAWA Test Equipment DLM2000 does not power on, it might be due to using a power supply outside the specified ratings. Use a correct power supply.
N
Nicole HarrisSep 4, 2025
What to do if keys do not work on my YOKOGAWA DLM2000 Test Equipment?
- M
  Micheal JohnsonSep 5, 2025
  If the keys on your YOKOGAWA Test Equipment DLM2000 do not work, it could indicate a malfunction. Perform a key test. If the test fails, servicing is required.
B
brianna25Sep 9, 2025
Why can't I print to the built-in printer on my YOKOGAWA DLM2000 Test Equipment?
- J
  Joshua MarshSep 9, 2025
  If you cannot print to the built-in printer of your YOKOGAWA Test Equipment DLM2000, it indicates that the printer head is damaged or worn out, which means servicing is required.

YOKOGAWA DLM2000 Series Specifications

General

Bandwidth	200 MHz, 350 MHz, 500 MHz
Channels	4
Sampling Rate	1.25 GS/s
Display	8.4-inch LCD
Vertical Resolution	8 bits
Trigger Types	Edge, Pulse Width, Serial Bus (I2C, SPI, CAN, LIN, UART)
Interface	USB
Power Supply	100-240 VAC, 50/60 Hz
FFT	Yes