YOKOGAWA DLM2000 Series - 5.31 SYSTem Group

5-196
IM 710105-17E
:SERialbus<x>:SENT[:ANALyze]:SETup:F
ORMat:CEFactor:SCPulses
Function Sets or queries the consecutive calibration pulse
error factor of SENT signal analysis.
Syntax
:SERialbus<x>:SENT[:ANALyze]:SETup:
FORMat:CEFactor:SCPulses {OFF|OPT2|PO
PTion}
:SERialbus<x>:SENT[:ANALyze]:SETup:
FORMat:CEFactor:SCPulses?
<x> = 1 to 4
Example
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CEFACTOR:SCPULSES OFF
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CEFACTOR:SCPULSES?
-> :SERIALBUS1:SENT:ANALYZE:SETUP:FOR
MAT:CEFACTOR:SCPULSES OFF
:SERialbus<x>:SENT[:ANALyze]:SETup:F
ORMat:CRCType
Function Sets or queries the SENT signal analysis CRC
computation type.
Syntax
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:CRCType {LEGacy|RECommended}
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:CRCType?
<x> = 1 to 4
Example
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CRCTYPE LEGACY
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CRCTYPE?
-> :SERIALBUS1:SENT:ANALYZE:SETUP:FOR
MAT:CRCTYPE LEGACY
:SERialbus<x>:SENT[:ANALyze]:SETup:F
ORMat:CTICk
Function Sets or queries the SENT signal analysis clock
tick value.
Syntax
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:CTICk {<NRf>}
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:CTICk?
<x> = 1 to 4
<NRf> = 1.00 µs to 100.00 µs (resolution:0.01 µs)
Example
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CTICK 0.000001
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CTICK?
-> :SERIALBUS1:SENT:ANALYZE:SETUP:FOR
MAT:CTICK 1.000000E-06
:SERialbus<x>:SENT[:ANALyze]:SETup:F
ORMat:CTOLerance
Function Sets or queries the SENT signal analysis clock
tolerance.
Syntax
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:CTOLerance {<NRf>}
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:CTOLerance?
<x> = 1 to 4
<NRf> = ±1.0% to ±30.0% (resolution:0.1%)
Example
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CTOLerance 25.0
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:CTOLERANCE?
-> :SERIALBUS1:SENT:ANALYZE:SETUP:FOR
MAT:CTOLERANCE 25.0E+00
:SERialbus<x>:SENT[:ANALyze]:SETup:F
ORMat:DNIBbles
Function Sets or queries the number of data nibbles for
SENT signal analysis.
Syntax
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:DNIBbles {<NRf>}
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:DNIBbles?
<x> = 1 to 4
<NRf> = 1 to 6
Example
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:DNIBBLES 6
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:DNIBBLES?
-> :SERIALBUS1:SENT:ANALYZE:SETUP:FOR
MAT:DNIBBLES 6
:SERialbus<x>:SENT[:ANALyze]:SETup:F
ORMat:PPULse
Function Sets or queries the presence or absence of pause
pulses for SENT signal analysis.
Syntax
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:PPULse {<Boolean>}
:SERialbus<x>:SENT[:ANALyze]:SETup:FO
RMat:PPULse?
<x> = 1 to 4
Example
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:PPULSE ON
:SERIALBUS1:SENT:ANALYZE:SETUP:FORMAT
:PPULSE?
-> :SERIALBUS1:SENT:ANALYZE:SETUP:FOR
MAT:PPULSE 1
5.24 SERialbus Group