ABB COMMANDER 351 - Index

95
INDEX
A
Accessories .............................................................. 1
Alarms ........................................................... 34, 47
Acknowledge ............................................... 5, 50
Acknowledge enable ....................................... 59
Configuration ................................................... 47
Global .............................................................. 50
Hysteresis ................................................. 49, 50
Set Up ............................................................. 34
Trip Settings .............................................. 34, 47
Type........................................................... 34, 49
Analog Backup Station..................................... 16, 84
Analog Inputs – Level 7 ......................................... 43
Broken Sensor ....................................44, 45, 46
Decimal Point ......................................43, 45, 46
Engineering Range ............................. 44, 45, 46
Calibration ....................................................... 68
Failure Action .................................................. 55
Analog Outputs 1 and 2 ......................................... 61
See Also: Digital Outputs 1 and 2
Electrical Ranges ...................................... 62, 64
Engineering Ranges ................................. 62, 64
Sources ..................................................... 62, 64
See Also: Rear Fold-out/ Table D
Analog Sources .................... Rear Fold-out/ Table D
Approach Band....................................................... 30
Auto-tune ................................................................ 21
Error................................................................. 21
Password......................................................... 60
Starting ............................................................ 23
Auto/Manual
Mode Selection Source.......................56, 57, 58
A/M Station Template ............................... 14, 74
A/M Switch .................................................. 4, 50
B
Bargraph ................................................................... 3
Increment ........................................................ 60
See Also: Relevant Operator
Template in Section 2
Basic Configuration – Level 6 ................................ 39
Boundless Control – see Motorized Valves
Broken Sensor Drive ..................................44, 45, 46
C
Calibration – see Analog Inputs
Calibration Error ....................................................... 9
Character Set ........................................................... 8
Clock Settings ........................................................ 60
Cold Junction
Compensation .....................................70, 77, 80
Failed ................................................................. 9
…C
Configuration Error ................................................... 9
Configuration Password ......................................... 60
Configured Outputs 1 to 3 ...................................... 57
See Also: Auto/Manual and Backup Templates
Control Action ......................................................... 42
Control Configuration – Level A............................. 54
Control Efficiency Monitor ...................................... 24
Control Set Point – see Set Points
Control Output Deadband ...................................... 31
Custom Linearizer .................................................. 87
D
Date and Time Setting ........................................... 60
Deadband
Control Output ................................................. 31
MV Feedback .................................................. 35
Default Outputs ..........................................52, 55, 57
Delay Timer ............................................................ 87
Derivative Action Time ........................................... 30
Deviation Alarms .................................................... 47
Digital Inputs 1 to 4 .......................................... 76, 77
See Also: Rear Fold-out/ Table C
Digital Outputs 1 and 2 .......................................... 61
Polarity ...................................................... 61, 63
Source ....................................................... 61, 63
Digital Sources ..................... Rear Fold-out/ Table C
Direct Control Action .............................................. 42
Displays .........................................................8, 9, 11
LCD Alphabet .................................................... 8
E
Electrical Connections ........................................... 76
Error Codes .............................................................. 9
F
Failure Modes
Analog Input .................................................... 55
Power Failure .................................................. 54
Process Variable ............................................. 55
Remote Set Point ............................................ 52
Fault-finding – see Error Messages
Fault Detection Level ............................................. 86
Feedback (Motorized Valves) ................................ 35
See Also: Analog Inputs (Process Variable)
Filter Time Constant ................................... 44, 45, 46
Fine Tuning....................................................... 25, 68
G
Gain Scheduling
Selection.......................................................... 58
Sources ........................................................... 58
Proportional and Integral Terms ..................... 29
Global Alarm Acknowledge Source ....................... 50
Glossary of Abbreviations ...................................... 10