Agilent Technologies, Inc.
2850 Centerville Road
Wilmington, DE 19808-1610
Agilent Technologies 2000
All Rights Reserved.
Reproduction, adaptation, or
translation without permission
is prohibited, except as allowed
under the copyright laws.
Part No. G1530-90307
First edition, Jan 2000
Printed in USA
Replaces Part No. G1530-90305
Site Preparation and
Installation Manual
HP® is a registered trademark
of Hewlett-Packard Co.
Microsoft® , Windows® , and
Windows NT® are registered
trademarks of Microsoft Corp.
Safety information
The 6890 Gas Chromatograph
meets the following IEC
(International Electrotechnical
Commission) classifications:
Safety Class 1, Transient
Overvoltage Category II, and
Pollution Degree 2.
This unit has been designed and
tested in accordance with
recognized safety standards and
designed for use indoors. If the
instrument is used in a manner
not specified by the
manufacturer, the protection
provided by the instrument may
be impaired. Whenever the
safety protection of the 6890
has been compromised,
disconnect the unit from all
power sources and secure the
unit against unintended
operation.
Refer servicing to qualified
service personnel. Substituting
parts or performing any
unauthorized modification to
the instrument may result in a
safety hazard. Disconnect the
AC power cord before removing
covers. The customer should
not attempt to replace the
battery or fuses in this
instrument. The battery
contained in this instrument is
recyclable.
Safety symbols
Warnings in the manual or on
the instrument must be
observed during all phases of
operation, service, and repair of
this instrument. Failure to
comply with these precautions
violates safety standards of
design and the intended use of
the instrument.
Agilent Technologies assumes
no liability for the customer's
failure to comply with these
requirements.
WARNING
A warning calls attention to a
condition or possible situation
that could cause injury to the
user.
CAUTION
A caution calls attention to a
condition or possible situation
that could damage or destroy
the product or the user's work.
See accompanying
instructions for more
information.
Indicates a hot
surface.
Indicates hazardous
voltages.
Indicates earth
(ground) terminal.
Indicates radio-active
hazard.
Indicates explosion
hazard.
Electromagnetic
compatibility
This device complies with the
requirements of CISPR 11.
Operation is subject to the
following two conditions:
1. This device may not cause
harmful interference.
2. This device must accept any
interference received,
including interference that
may cause undesired
operation.
If this equipment does cause
harmful interference to radio or
television reception, which can
be determined by turning the
equipment off and on, the user
is encouraged to try one or
more of the following measures:
1. Relocate the radio or
antenna.
2. Move the device away from
the radio or television.
3. Plug the device into a
different electrical outlet, so
that the device and the radio
or television are on separate
electrical circuits.
4. Make sure that all peripheral
devices are also certified.
5. Make sure that appropriate
cables are used to connect the
device to peripheral
equipment.
6. Consult your equipment
dealer, Agilent Technologies,
or an experienced technician
for assistance.
7. Changes or modifications not
expressly approved by
Agilent Technologies could
void the user’s authority to
operate the equipment.
Sound Emission
Certification for Federal
Republic of Germany
Sound pressure Lp < 65 dB(A)
During normal operation
At the operator position
According to ISO 7779 (Type
Test)
When operating the 6890 with
cryo valve option, the sound
pressure 74.6 dB(A) during cryo
valve operation for short burst
pulses.
Schallemission
Schalldruckpegel LP < 65 dB(A)
Am Arbeitsplatz
Normaler Betrieb
Nach DIN 45635 T. 19
(Typprüfung)
Bei Betrieb des 6890 mit Cryo
Ventil Option treten beim
Oeffnen des Ventils
impulsfoermig Schalldrucke Lp
bis ca. 74.6 dB(A) auf.
To Next Page
Loading...
