Atlas Copco ACTA 3000 - Page 128

Technical specifications ACTA 4000 User Guide
128 (136) 2008-12 9836 4171 01
Q.prog selection No controller Other
controller
F2000/PF2000
Manual input
F2000/PF2000
RS232
DS/DL
Manual input
Measure delay time
0 ms 0 ms 0 ms Read from controller 0 ms
Reset time
0 ms 0 ms 0 ms Read from controller 0 ms
End time
400 ms 400 ms 400 ms Read from controller 400 ms
Slip torque2
0.1 Nm 0.1 Nm 0.1 Nm 0.1 Nm 0.1 Nm
Batch size
0 0 0 Read from controller 0
Subgroup size
5 5 5 Read from controller 5
Subgroup
frequency
1 1 1 1 1
Batch result
Off Off Off Read from controller Off
Torque min
0.05 * TCT 0.05 * TCT 0.05 * TCT Read from controller 0.05 * TCT
Torque max
TCT * TTS TCT * TTS TCT * TTS Read from controller TCT * TTS
Torque LCLx
-9999.0 -9999.0 -9999.0 -9999.0 -9999.0
Torque UCLx
9999.0 9999.0 9999.0 9999.0 9999.0
Torque LCLr
0.0 0.0 0.0 0.0 0.0
Torque UCLr
9999.0 9999.0 9999.0 9999.0 9999.0
Torque CM >
0.0 0.0 0.0 0.0 0.0
Torque CMK >
0.0 0.0 0.0 0.0 0.0
Torque CAM >
0.0 0.0 0.0 0.0 0.0
Torque diff % <
9999.0 9999.0 9999.0 9999.0 9999.0
Angle min
0.0 0.0 0.0 Read from controller 0.0
Angle max
9999.0 9999.0 9999.0 Read from controller 9999.0
Angle LCLx
-9999.0 -9999.0 -9999.0 -9999.0 -9999.0
Angle UCLx
9999.0 9999.0 9999.0 9999.0 9999.0
Angle LCLr
0.0 0.0 0.0 0.0 0.0
Angle UCLr
9999.0 9999.0 9999.0 9999.0 9999.0
Angle CM >
0.0 0.0 0.0 0.0 0.0
Angle CMK >
0.0 0.0 0.0 0.0 0.0
Angle CAM >
0.0 0.0 0.0 0.0 0.0
Angle diff % <
9999.0 9999.0 9999.0 9999.0 9999.0
No. of pulses min
0 0 0 0 0
No. of pulses max
9999 9999 9999 9999 9999
Parameter 1
Torque Torque Torque Torque Torque
Statistical
parameter 1
Mean, σ
Contr, Diff Contr, Diff Contr, Diff
Mean, σ
Torque units
Torque units set
by Config.
Torque units set
by Config.
Torque units set by
Config.
Read from controller Torque units set
by Config.
Pulse units
Pulse units set by
Config.
Pulse units set by
Config.
Pulse units set by
Config.
Pulse units set by
Config.
Pulse units set
by Config.
2
Not used for wrench.