Barco FLM R22+ - Installation of the front cover

243 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

16. Servicing

A

Image 16-13

5. Switch off the projector, wait ﬁve minutes and unplug the power cord at the projector side.

6. Reinstall the cover of the lamp, see "Installation of the lamp cover", page 198.

192

R59770179 FLM R22+ 15/03/2010

Table of Contents

Default Chapter3
- Disposal Information3
- Software License Agreement3
- Table of Contents5
1 Safety9
- General9
- Important Safety Instructions10
- Important Warnings Concerning FLM Flight Cases13
2 General15
- Installation Requirements15
- Unpacking the Projector16
- Box Content17
- FLM Flight Case18
- Projector Conﬁgurations18
- Rear Projection19
- Positioning the Projector20
- Shift Range20
- Projector Air Inlets and Outlets22
- Free Download of Projector Toolset22
3 Physical Installation23
- Remote Control Unit (RCU)23
- Lenses27
- Alignment of a Table Mount FLM Projector31
- Alignment of a Ceiling Mount FLM Projector31
- Suspension of the FLM Projector with Rigging Clamps32
4 Stacking FLM Projectors35
- Aligning Stacked FLM Projectors37
5 Connections39
- Power Connection39
- Input Source Connections41
- Communication Connections42
- Projector Status42
- Usb Port45
6 Getting Started47
- RCU & Local Keypad47
- Terminology Overview47
- Operating the Projector49
- Using the RCU51
- Quick Setup Adjustments53
- Projector Address56
  - Displaying and Programming Addresses56
  - Controlling the Projector57
- Source Selection57
- Controlling the Projector58
7 Start up of the Adjustment Mode59
- About the Adjustment Mode59
- About the Use of the Remote Control and the Local Keypad59
- Start up the Adjustment Mode59
- Navigation and Adjustments60
- Shortcut Keys to the Menus60
- On Screen Menus Versus LCD Display Menus61
- Test Patterns in Adjustment Mode61
- Menu Memory61
8 Input Menu63
- Overview Flow63
- Slot Module Type63
  - About Input Setup63
  - Input Conﬁguration64
- Input Locking65
- Minimum Delay67
- Native Resolution67
- Source Switching69
- No Signal69
9 Image Menu73
- Overview Flow73
- How to Select the Image Adjustments74
- Image Settings74
- Aspect Ratio86
- Timings87
- Image Files Services92
- Save Custom Settings97
10 Layout Menu99
- Overview Flow99
- Main Window99
- PIP Window104
- Layout File Services110
- Zoom - Focus113
11 Lamp Menu115
- Overview Flow115
- Lamp Power Mode115
- Lamp Power116
- Constant Light Output Mode (CLO Mode)117
- CLO Target118
- Lamp Identiﬁcation118
- Z-Axis Adjustment119
12 Alignment Menu121
- Overview Flow121
- Orientation122
- Lens Adjustment123
- Side Keystone124
- Warp Geometry Settings125
- Contrast Enhancement134
- Blanking134
- How to Adjust the Blanking135
- Gamma136
- Internal Pattern136
- Color Space137
- Scenergix138
13 Projector Control149
- Overview Flow149
- Projector Address150
  - Individual Projector Address150
  - Common Address151
- Serial Communication152
- Network153
- IR Control Switching157
- Art-Net DMX157
- Buttons162
- Menu Position164
  - On Screen Menu164
  - Bar Scale165
- Local LCD165
  - Local LCD Time out165
  - Local LCD Contrast166
- Language Selection166
- How to Change the Language167
14 Service Menu169
- Overview Flow169
- Identiﬁcation170
- Diagnosis171
- Convergence176
- Internal Service Patterns177
- Restore Factory Defaults178
- Reset Formatter179
- Save Custom Settings180
- Reﬁll Mode180
- Broadcast Mode181
- USB Memory182
15 Maintenance185
- Replacement of the Dust Filter on the Front Side185
- Replacement of the Dust Filter on the Bottom Side186
- Replacement of the Dust Filter on the Top Side187
- Pressure Veriﬁcation of the Liquid Cooling Circuit187
- Cleaning the Lens188
- Cleaning the Exterior of the Projector188
16 Servicing189
- Removal of the Lamp House189
- Removal of the Input & Communication Unit190
- Removal of an Input Module191
- Installation of the Lamp House192
- Installation of the Input & Communication Unit193
- Installation of an Input Module194
- Realignment of the Lamp in Its Reﬂector195
17 Removal of the Projector Covers197
- Removal of the197
- Removal of the Side Cover198
- Removal of the Lamp Cover199
- Removal of the Input Cover199
- Installation of the200
- Installation of the Side Cover201
- Installation of the Lamp Cover202
- Installation of the Input Cover203
18 Dimensions205
- Dimensions of the FLM R22205
- Dimensions of the FLM Flight Case206
- Dimensions of the Rigging Clamps207
19 Standard Source Files209
- Table Overview209
20 DMX Chart211
- DMX Chart, Basic211
- DMX Chart, Extended212
- DMX Chart, Full213
21 Troubleshooting217
- Error Codes217
22 Speciﬁcations225
- Speciﬁcations FLM R22225
- Specifications226
- Speciﬁcations FLM 5 Cable Input (Multi Purpose)228
- Speciﬁcations FLM HDSDI - SDI Input229
- Speciﬁcations FLM DVI Input230
- Speciﬁcations FLM DVI HDCP Input231
23 Order Information233
- Spare Part Order Info233
Glossary235
Index237

Other manuals for Barco FLM R22+

Brochure & Specs4 pages

Related product manuals

Preview: Barco FLM HD20

Preview: Barco FLM series

Barco FLM series

Preview: Barco FL40 series

Barco FL40 series

Preview: Barco F50

Preview: Barco F90

Preview: Barco F70

Preview: Barco Freya

Preview: Barco F80-Q7

Preview: Barco F80 series

Barco F80 series

Barco F22 series

Preview: Barco F90 - W13WUXGA

Barco F90 - W13WUXGA