EasyManuals Logo

Bender ISOMETER isoRW425 User Manual

Bender ISOMETER isoRW425
76 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #69 background imageLoading...
Page #69 background image
Technical data
69
isoRW425_D00052_03_M_XXEN / 02.2017
Displays, memory
Display..................................................................................................... LC display, multi-functional, not illuminated
Display range measured value insulation resistance (R
F
) ........................................................................ 1 kΩ…4 MΩ
Display range measured value impedance (Z
F
) with f
n
= 50 / 60 Hz..................................................... 1 kΩ…1 MΩ
Operating uncertainty (R
F
in R mode, Z
F
in Z mode)............................................................... ± 15 %, at least ±1 k
Display range measured value nominal system voltage (U
n
) ........................................................... 0…500 V r.m.s.
Operating uncertainty.................................................................................................................. ± 5 %, at least ± 5 V
Display range measured value system leakage capacitance of R
F
> 10 kΩ .............................................. 0…300 F
Operating uncertainty............................................................................................................... ± 15 %, at least ± 2 µF
Display range measured value system leakage capacitance of Z
F
> 10 kΩ ............................................. 1 nF…1 F
Operating uncertainty (Z
F
X
c
)............................................................................................... ± 15 %, at least ± 2 nF
Password .................................................................................................................................... off / 0…999 (0, off)*
Fault memory alarm messages ..................................................................................................................... on / (off)*
Interface
Interface/protocol................................................................................................. RS-485/BMS, Modbus RTU, isoData
Baud rate ............................................................BMS (9.6 kbit/s), Modbus RTU (selectable), isoData (115.2 kbits/s)
Cable length (9.6 kbits/s) .............................................................................................................................. ≤ 1200 m
Cable: twisted pairs, shield connected to PE on one side .............................................................. min. J-Y(St)Y 2x0.6
Terminating resistor.................................................................................. 120 Ω (0,25 W), internal, can be connected
Device address, BMS bus, Modbus RTU ..................................................................................................... 3…90 (3)*
Switching elements
Switching elements...................................................................................... 2 x 1 N/O contacts, common terminal 11
Operating principle ............................................................................N/C operation/N/O operation (N/O operation)*
Electrical endurance, number of cycles ............................................................................................................... 10000
Contact data acc. to IEC 60947-5-1:
Utilisation category.............................................................. AC-12..........AC-14 ..........DC-12 ..........DC-12 ....... DC-12
Rated operational voltage .....................................................230 V...........230 V.............24 V.......... 110 V........ 220 V
Rated operational current ........................................................ 5 A...............2 A ...............1 A ........... 0.2 A ......... 0.1 A
Minimum contact rating ............................................................................................................ 1 mA at AC/DC 10 V
Environment/EMC
EMC ......................................................................................................................... IEC 61326-2-4, DIN EN50121-3-2
Ambient temperatures:
Operation ................................................................................................................................................ -40…+70 ºC

Table of Contents

Other manuals for Bender ISOMETER isoRW425

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Bender ISOMETER isoRW425 and is the answer not in the manual?

Bender ISOMETER isoRW425 Specifications

General IconGeneral
BrandBender
ModelISOMETER isoRW425
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals