Bosch Rexroth IPC - Page 97

Appendix
A–3
1070 073 822-104 (02.06) GB
MB, A–1
mouse port, 6–21
MTB, A–1
O
operating conditions, 2–4
operating power, 230/115 VAC, 5–8
operating status, LED display, 7–1
OS software, 9–1
P
PCI, A–1
PCI slot, 8–12
PE conductor system, 5–2
PE connections, 5–2
pin assignment
COM1 through COM4, 6–3
LPT1, 6–9
ports / connectors, overview, 6–1
ports and connectors, battery terminal, 8–10
power supplies, 5–5
power supply connection, X11, 6–18
Protection Category, 2–4
PS/2 keyboard port, 6–19
PS/2 mini DIN to MF2 keyboard adapter , 6–19
PS/2 mouse port, 6–21
Q
qualified personnel, 1–2
R
RAM, A–1
rechargeable battery pack, 2–3
relative humidity, 2–4
release information, 1–7
replacing
battery pack, 8–9
CD–ROM drive, 8–6
floppy disk, 8–7
hard disk, 8–4
RESET button, 7–1
RS–232 interface, COM1, 6–3
RS–422/485 interface, COM1, 6–3
S
safety instructions, 1–4
safety instructions, specific, 1–5
approved spare parts, 1–5
Emergency–OFF safety devices, 1–5
maintenance procedures, 1–5
measuring / testing procedures, 1–5
retrofits / modifications, 1–5
safety markings, 1–3
safety transformer, 5–5
screening information, 5–2
Shutdown Delay Time, 3–11
software, 9–1
spare parts, 1–5
specifications, 2–2
SPP, A–1
standard operation, 1–1
standards compatibility, 2–5
storage temperature, 2–4
system overview, 2–1
T
temperature, 2–4
temperature monitoring, 3–1
TFT, A–1
TFT display, resolution, 6–11
trademarks, 1–7
U
uninterruptible power supply, 3–2
UPS program, 3–4
UPS, A–1
UPS functionality, 3–2
UPS program
configuration, UPSnt for IPC300 (Windows NT), 3–13
default settings, 3–8
Functionality, 3–4
UPSnt for IPC (Windows NT), configuration, 3–10
UPSnt for IPC, default settings, 3–12
UPSnt for IPC300, default settings, 3–16
UPSnt, operating, 3–9
UPSplus Mode, command, 3–8
UPSplus, operating, 3–5
UPSnt for IPC300, program, 3–15
COM port, 3–13
Command, dialog, 3–15
configuration, 3–13
Default, button, 3–16
Enable Fan Control, 3–14
Enable Temp Control, option, 3–14
Enable Voltage Control, option, 3–15
Health Monitor, dialog section, 3–16
No Powerdown on Shortbreak, option, 3–15
Shutdown Count, option, 3–16
Shutdown Delay Time, 3–14
Startup Battery Test, 3–14
UPSnt, program, 3–9
COM port, 3–10
configuration, 3–10
Default, button, 3–12
Disable Auto Power Off, option, 3–12
Enable Accu Test, option, 3–11
Enable Temp Control, option, 3–11
operation, 3–9
Shutdown Count, option, 3–12
Shutdown Delay Time, 3–11