69
gnge
U
N
110V ; 125V Fi1= 2,5A
230V ; 245V F1= 1,25A
50/60 Hz
Ringkerntrafo
4
Fi 1
Netzschalter
3
2
1
0V
+15V
-15V
110V
230V
5
5
2
1
3
4
Spannung_Trafo
T2,5 A
T5 A
T5 A
T5 A
T5 A
10. Repairs
10.1 Adjusting mains voltage for toroidal mains transformer
Before putting the Bosch Emissions Analysis into operation, you
must check that the set voltage of the toroidal mains transformer
is the same as that of the mains voltage. The Bosch Emissions
Analysis is factory-set to 230V.
! The transformer mains voltage may only be set by authorized
Service personnel. The Bosch Emissions Analysis must be
off circuit.
1. Remove housing cover.
2. Remove connection cable 5 of the toroidal mains transformer
(see diagram) from the mains input connector.
3. Connect the required connection cable (see diagram) to the
mains input connector.
Possible settings (see table):
230V (factory setting), 245V, 125V, 110V, 95V.
4. Close housing cover.
5. Perform safety test as per regulations in country of use (e.g.
to VDE in Germany).
Mains voltage Transformer voltage
230V 110V -15V +15V 0V
230V X X
245V X X
125V X X
110V X X
95V X X
i If the mains voltage connection changes, the adhesive label
on the rear of the unit bearing the voltage must be replaced.
10.2 AC / DC voltage supply to control module PCB
Voltage supply AC
Connector X 18:
Pin 3 (⊥) to Pin 1 = ~ 14.5 V
Pin 3 (⊥) to Pin 2 = ~ 11 V
Pin 3 (⊥) to Pin 4 = ~ 11 V
Pin 3 (⊥) to Pin 5 = ~ 14,5 V
Pin 7 (⊥) to Pin 6 = ~ 22 V
Voltage supply for RTM 430
Connector X 3:
Pin 4 (⊥) to Pin 6 = ~ 14.5 V
Pin 4 (⊥) to Pin 7 = ~ 14.5 V
Pin 4 (⊥) to Pin 8 = ~ 14.5 V
Pin 5 (⊥) to Pin 10 = ~ 14.5 V
Pin 5 (⊥) to Pin 11 = ~ 14.5 V
Pin 5 (⊥) to Pin 12 = ~ 14.5 V
Voltage supply for TFT display
Connector X 4:
Pin 2 of connector X4 carries extremely high voltage.
Only measure the voltage using a high-voltage probe.
Pin 1 (⊥) to Pin 2 = 1 KV
Voltage supply for OBD PCB
Connector X 6:
Pin 9 (⊥) to Pin 2 = + 5 V
Pin 9 (⊥) to Pin 4 = + 5 V
Pin 9 (⊥) to Pin 6 = - 12 V
Pin 9 (⊥) to Pin 8 = + 12 V
Voltage supply for RPM/temperature PCB
Connector X8:
Pin 1 (⊥) to Pin 2 = + 5 V
Pin 1 (⊥) to Pin 4 = + 5 V
Pin 1 (⊥) to Pin 6 = - 12 V
Pin 1 (⊥) to Pin 8 = + 12 V
Pin 1 (⊥) to Pin 11 = 9 V - 16 V
Pin 1 (⊥) to Pin 13 = 9 V - 16 V
Pin 1 (⊥) to Pin 16 = - 5 V
Voltage supply for heating
Connector X 19:
Pin 3 (⊥) to Pin 1 = + 12 V
Pin 3 (⊥) to Pin 2 = 9 V - 16 V
Voltage supply for exhaust-gas analyzer module
Connector X 22:
Pin 1 (⊥) to Pin 2 = 9 V - 16 V
Voltage supply for pump
Connector X 24:
Pin 1 (⊥) to Pin 3 = + 12 V
Voltage supply for pressure switch/pressure sensor
Connector X 25:
Pin 1 (⊥) to Pin 2 = + 5 V
Voltage supply for solenoid valve
Connector X 26:
Pin 1 (⊥) to Pin 2 = + 12 V
Voltage supply for NO2 measuring sensor
Connector X 34:
Pin 3 (⊥) to Pin 1 = + 12 V
Toroidal mains transformer
Power switch
To Next Page
Loading...
