Home
Brooks
Controller
GF Series
Brooks GF Series Supplemental Manual
4
of 1
of 1 rating
54 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Installation and Operatio
n Manual
X-DPT
-EtherCAT-GF1XX-MFC-
eng
Part Num
ber: 541B219AAG
April, 2017
53
Section 5-
A
ppendix
Brooks EtherCAT
MFCs
0x600F:03
–
Ram
p Active is set when
the device is ram
ping from one
setpoint to another. T
he bit is c
leared when the ramp i
s complete.
0xF383 bit 5
–
Acti
ve Device Error Detai
ls, Ramp Data is set when
an
invalid
Ramp Time is rec
eived. The bit is cleared
when a valid ramp tim
e is
received.
0xF383 bit 6
–
Acti
ve Device Error Detai
ls, Ramp Error is set
when a Ram
p
Time of zero is recei
ved by the device when a ram
p is active.
52
54
Table of Contents
Table of Contents
5
General Information
9
Introduction
9
Definition of Terms
10
Numbers
10
Table 1-1 - Definition of Terms
10
Quick Start
11
Master Hardware
11
Physical Interfaces
12
Power Supply
12
Figure 2-1 - Top View of GF Ethercat Device
12
Leds
13
Figure 2-2 - M8 Power Connector Location
13
Figure 2-3 - M8 Power Connector Drawing
13
Table 2-1 - RUN Indicator States
14
Table 2-2 - ERROR Indicator States
14
Exceptions Display Codes and Reporting
15
Table 2-3 - Display Code Summary
15
Slave Configuration
17
Introduction
17
Table 3-1 - Object Dictionary Structure
17
Process Data Object (PDO) Mapping
18
Rxpdo Mapping
18
Txpdo Mapping
19
Table 3-2 - Default Rxpdo (MFC/EMFC Profiles)
19
Table 3-3 - Default Rxpdo (MFM/EMFM Profiles)
19
Table 3-4 - Default Txpdo (EMFC Profile)
19
Table 3-5 - Default Txpdo (MFC Profile)
20
Table 3-6 - Default Txpdo (MFM Profile)
20
Table 3-7 - Default Txpdo (EMFM Profile)
20
Communication Specific Data
21
Table 3-8 - Communication Specific Data
21
Manufacturer Specific Data
22
Manufacturer Specific Inputs
23
Manufacturer Specific Configuration Data
23
Table 3-9 - Manufacturer Specific Inputs
23
Table 3-10 - Manufacturer Specific Configuration Data
23
SDP Device Type Specific Data
24
Input Data
24
Table 3-11 - Input Data
24
Output Data
25
Table 3-12 - Output Data
25
Configuration Data
26
Table 3-13 - Configuration Data
26
Information Data
27
Table 3-14 - Information Data
27
Semi Device Profile Area
29
Table 3-15 - Semi Device Profile
29
Value Range Setting
30
Exception Handling Data
30
Table 3-16 - Value Range Setting
30
Manufacturer Specific Device Data
32
Table 3-17 - Manufacturer Specific Device Data
32
SDP and CDP Device Specific Inputs
33
SDP and CDP Device Specific Information Data
33
Table 3-18 - SDP and CDP Device Specific Inputs
33
Table 3-19 - SDP and CDP Device Specific Information Data
33
SDP and CDP Command Objects
35
Table 3-20 - SDP and CDP Command Objects
35
Exceptions Implementation
41
Table 4-1 - Objects for Reporting and Controlling Exceptions
42
Table 4-2 - Device Errors
43
Table 4-3 - Manufacturer Errors
43
Error and Warning Condition Descriptions
44
Table 4-4 - Manufacturer Warnings
44
Non-Volatile Memory Failures (Display Codes 1,2,3)
45
Network Interface Failure (Display Code 4)
45
Selected Calibration Invalid (Display Code 5)
45
Identity Information Mismatch (Display Code 6)
45
Hardware Incompatibility (Display Code 7)
46
Flow Sensor Failure & Error (Display Code 10 and 110)
46
Flow Sensor Cooling Recovery (Display Code 111)
46
Excessive Drift (Display Code 112)
46
Process Flow out of Range (Display Codes 115 and 116)
46
Table 4-5 - User Specified Flow Limits
46
Pressure Sensor Error (Display Code 120)
47
Process Pressure out of Range (Display Codes 125 and 126)
47
Temperature Sensor Failure & Error (Display Code 130 and 10)
47
Table 4-6 - User Specified Pressure Limits
47
Temperature out of Range (Display Codes 135 and 136)
48
Excessive Leak-By (Display Code 142)
48
Control Deviation out of Limits (Display Code 145)
48
Table 4-7 - Control Deviation out of Limits
48
Temperature Stability (Display Code 230)
49
Mounting Orientation Alert (Display Code 251)
49
Voltage Input out of Limits (Display Code 260)
49
Totalizer Overflow Alert (Display Code 270)
49
Warm-Up (Display Code 299)
49
Device ID Switch Changed Alert (no Display Code)
50
Appendix
51
Ramping Feature
51
Figure 5-1 - Ramping Feature
52
Other manuals for Brooks GF Series
Installation And Operation Manual
62 pages
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Brooks GF Series and is the answer not in the manual?
Ask a question
Brooks GF Series Specifications
General
Brand
Brooks
Model
GF Series
Category
Controller
Language
English
Related product manuals
Brooks GF100 Series
68 pages
Brooks GF120XSL Series
62 pages
Brooks MFM
52 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
