MANUALPC-2012 Page 1
CONTROLLER STARTUP .................................................22
Initial Reset .....................................................................22
Configuration Menu .........................................................22
Alarm Buzzer...................................................................22
Bypass Line.....................................................................22
Battery Check..................................................................22
PPM Board Initialization ..................................................22
CHEMICAL CONTROL ......................................................22
Initial Activation of Sensors .............................................22
Bypass Line Test.............................................................22
Water Chemistry Adjustment...........................................22
Water Sampling...............................................................22
pH Calibration .................................................................22
pH Feed (Acid or Base)...................................................23
pH Setpoint .....................................................................23
ORP Calibration ..............................................................23
ORP Setpoint ..................................................................23
Sanitizer Calibration ........................................................23
Time Limits......................................................................23
Shock Treatment .............................................................23
Chemical Saver...............................................................23
WATER SATURATION ......................................................23
CHAPTER IV - CONTROLLER OPERATION..............24
Access.............................................................................24
Default Setup ..................................................................24
8 - CONFIGURATION MAIN MENU ...................................24
8.1 - INITIAL SETUP SUBMENU ....................................25
8.1.1 - Language..........................................................25
8.1.2 - Units .................................................................25
8.1.3 - Code Number ...................................................25
8.1.4 - Clock ................................................................26
8.1.5 - Readings ..........................................................26
8.1.6 - Data Logging ....................................................26
8.1.7 - Model Options ..................................................26
8.2 - OPERATIONS SUBMENU......................................27
8.2.1 - Audio Alarms ....................................................27
8.2.2 - Bypass Line......................................................27
8.2.3 - Langelier Saturation Index................................27
8.2.4 - Reset ................................................................28
8.2.5 - Backup Battery .................................................28
8.2.6 - Probe Monitor ...................................................28
8.3 - REPORT SUBMENU ..............................................28
8.3.1 - View Data Log ..................................................28
8.3.2 - Print Reports.....................................................29
On-Site Printing ...........................................................29
On-Site Download........................................................29
8.4 - COMMUNICATIONS SUBMENU............................30
8.4.1 - Phone Numbers................................................30
8.4.2 - Unit Identification..............................................30
8.4.3 - Alarm Calling ....................................................30
8.4.4 - 4-20 mA Output ................................................30
1 - ORP MENU....................................................................31
Operation.....................................................................31
1.1 - Control Mode...........................................................31
1.2 - Display and Calibration ...........................................31
1.3 - Setpoint...................................................................31
1.4 - Low Alarm...............................................................31
1.5 – High Alarm .............................................................32
1.6 - Time Limit ...............................................................32
1.7 - Run Time ................................................................32
1.8 - Last Shock ..............................................................32
1.8.1 - Shock Treatment ..............................................32
1.8.2 - Deshock............................................................32
1.8.3 - Chemical Saver ................................................32
2 - SANITIZER MENU ........................................................ 33
Input Selection ................................................................33
Free Chlorine Control......................................................33
Calculated PPM Readings .............................................. 33
2.1 - Display and Calibration ...........................................33
Free Chlorine Calibration.............................................33
Calculated PPM Calibration.........................................33
2.3 - Setpoint...................................................................34
2.4 - Low Alarm...............................................................34
2.5 - High Alarm ..............................................................34
2.6 - Time Limit ...............................................................34
2.7 - Run Time ................................................................34
2.8 - Last Shock ..............................................................34
2.8.1 - Superchlorination .............................................34
2.8.2 - Deshock ...........................................................34
2.8.3 - Chemical Saver................................................34
3 - PH MENU....................................................................... 35
Operation ........................................................................35
3.1- Control Mode ........................................................... 35
3.2 - Display and Calibration ...........................................35
3.3 - Setpoint...................................................................35
3.4 - Low Alarm...............................................................36
3.5 - High Alarm ..............................................................36
3.6 - Time Limit ...............................................................36
3.7 - Run Time ................................................................36
3.8 - Probe Clean............................................................36
4 - CONDUCTIVITY MENU ................................................ 37
Conductivity and TDS .....................................................37
Conductivity or TDS Displays..........................................37
4.1- Control Mode ........................................................... 37
4.2 - Display and Calibration ...........................................37
4.3 - Setpoint...................................................................37
4.4 - Low Alarm...............................................................37
4.5 - High Alarm ..............................................................37
4.6 - Time Limit ...............................................................38
4.7 - Run Time ................................................................38
4.8 - Select Scale............................................................38
4.8.1 - Scale Selection.................................................38
4.8.2 - Cell Constant....................................................38
4.8.3 - TDS Factor.......................................................38
5 - TEMPERATURE MENU ................................................39
Operation ........................................................................39
5.1 - Control Mode ..........................................................39
5.2 - Display and Calibration ...........................................39
5.3 - Setpoint...................................................................39
5.4 - Low Alarm...............................................................39
5.5 - High Alarm ..............................................................39
5.6 - Time Limit ...............................................................39
5.7 - Run Time ................................................................39
5.8 - Energy Saver ..........................................................39
6- PUMP MENU.................................................................. 40
Operation ........................................................................40
6.1- Control Mode ........................................................... 40
6.2 - Influent Pressure.....................................................41
Pressure Alarms..........................................................41
Calibration ...................................................................41
6.3 - Effluent Pressure ....................................................41
Differential Pressure .......................................................41
6.4 - Flow Rate.................. E
rror! Bookmark not defined.
6.5 - Flow Total ................. Error! Bookmark not defined.
6.6 - Heater Delay (Cooldown Safety) ........................... 43
6.7 - Water Level Control ................................................ 43
7 - FILTER MAIN MENU.....................................................44
Filter Backwash...............................................................44
7.1 - Automatic Backwash...............................................44
7.1.2 - Pressure Differential.........................................45
To Next Page
Loading...
