EasyManua.ls Logo

CHINT NVF2G-S Series

CHINT NVF2G-S Series
115 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Fd.22
Fd.25
Fd.32
reserve
reserve
reserve
Fd.20
Fd.21
Fd.23
Fd.24
Fd.33
Fd.34
Fd.26
Fd.27
Fd.28
Fd.29
Fd.30
Fd.31
0.00V
0.00V
0.00%
0.00%
0
0.0 °C
0.0%
0.0%
0.0%
0.0%
0.0%
0.0%
AI1 input voltage
AI2 input voltage
AI1 adjusted percentage
AI2 adjusted percentage
PLC current segment number
radiator temperature
AO1 output
AO2 output
Process closed-loop given
Process Closed Loop Feedback
process closed loop error
Process closed loop output
(-10.00~+11.00)V
(-10.00~+11.00)V
(-100.00 ~ 110.00)%
(-100.00 ~ 110.00)%
0 ~ 15
(0.0200.0) ℃
(0.0 ~ 100.0)%(relative to the percentage of full scale)
(0.0 ~ 100.0)%(relative to the percentage of full scale)
(0.0 ~ 100.0)%(relative to the percentage of full scale)
(0.0 ~ 100.0)%(relative to the percentage of full scale)
(0.0 ~ 100.0)%(relative to the percentage of full scale)
(0.0 ~ 100.0)%(relative to the percentage of full scale)
Fd.18
Fd.19
0x0000
0x0000
Digital input terminal state
Switch output terminal state
Setting range: 0x0000~0xFFFF
0: disconnected
1: closed
Units:
BIT0BIT3:X1X4
ten digits:
BIT0:X5
BIT1:X6
BIT2~BIT3: reserved
Setting range: 0x0000~0xFFFF
0: disconnected;
1: closed
Units:
BIT3 : Y1, RO1 , RO2
Tens: Reserved
function
code
name
Parameter Description
Defaults
Change
Fd.10
Fd.11
Fd.12
Fd.13
Fd.14
Fd.15
Fd.16
Fd.17
(-300.0 ~ +300.0)% (compared to twice the rated
torque of the motor)
(-300.0 ~ +300.0)%
(0 ~ 100.0)%
(0.02000.0)kW
(-300.00 ~ +300.00)Hz
(-300.00 ~ +300.00)Hz
(0 ~ 800)V
0.0%
0.0%
0.0%
0.1kW
0.00Hz
0.00Hz
0
0x0000
ASR controller output
Torque current
flux current
Motor Power
Motor estimated frequency
Motor measured frequency
bus voltage
Inverter running status
Setting range: 0x0000~0xFFFF
Bit0: run/stop
Bit1: reverse/forward
Bit2: Zero speed running
Bit3: Accelerating
Bit4: Decelerating
Bit5: Constant speed running
Bit6: Pre-excitation
Bit7: Self-learning
Bit8: Overflow stall
Bit9: DC overvoltage stall
Bit10: speed limit
Bit11: frequency limit
Bit12: Inverter fault
Bit13: Operation preparation completed
Bit14: reserved
Bit15: undervoltage/normal
102
NVF2G-S Series Inverter User's Guide

Table of Contents

Related product manuals