Cisco 7941G Administration Guide

Table 36: EnergyWise Configuration Fields
DescriptionField
Selects the schedule of days for which the phone powers off. Select
multiple days by pressing and holding the Control key while clicking
on the days for the schedule.
By default, no days are selected.
When Enable Power Save is checked, you receive a message to warn
about emergency (e911) concerns.
While Power Save Plus mode (hereafter, the mode) is in
effect, endpoints configured for the mode are disabled for
emergency calling and from receiving inbound calls. By
selecting this mode, you agree to the following: (i) you are
taking full responsibility for providing alternate methods
for emergency calling and receiving calls while the mode
is in effect; (ii) Cisco has no liability in connection with
your selection of the mode and all liability in connection
with enabling the mode is your responsibility; and (iii) you
will inform users of the effects of the mode on calls, calling
and otherwise.
Caution
To disable Power Save Plus, you must uncheck the Allow
EnergyWise Overrides check box. Leaving the Allow
EnergyWise Overrides checked with no days selected in the
Enable Power Save Plus field does not disable Power Save
Plus.
Note
Enable Power Save Plus
Determines when the phone automatically turns on for the days selected
in the Enable Power Save Plus field.
Enter the time in this field in 24 hour format, where 00:00 is midnight.
For example, to automatically power up the phone at 7:00 a.m. (0700),
enter 7:00. To power up the phone at 2:00 p.m. (1400), enter 14:00.
The default value is blank, which means 00:00.
Phone On Time
The time of day that the phone powers down for the days selected in
the Enable Power Save Plus field. If the Phone On Time and the Phone
Off Time fields contain the same value, the phone does not power
down.
Enter the time in this field in 24 hour format, where 00:00 is midnight.
For example, to automatically power down the phone at 7:00 a.m.
(0700), enter 7:00. To power down the phone at 2:00 p.m. (1400),
enter 14:00.
The default value is blank, which means 00:00.
Phone Off Time
Cisco Unified IP Phone 7941G, 7941G-GE, 7942G, 7961G, 7961G-GE, and 7962G Administration Guide for Cisco
Unified Communications Manager 9.0 (SCCP and SIP)
154
Features, Templates, Services, and Users
EnergyWise Setup on Cisco Unified IP Phone

Cisco 7941G Specifications

General

Keypad number of keys	12
Touchscreen	-
Display resolution	320 x 222 pixels
Speakerphone	Yes
Voice codecs	G.729a
Bluetooth	No
Supported network protocols	DHCP, TFTP, SCCP, DSCP
Ethernet LAN (RJ-45) ports	2
Input voltage	48 V
Dimensions (WxDxH)	266.7 x 152.4 x 203.2 mm
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Handset type	Wired handset
Product type	IP Phone
Product color	Gray
Safety	(UL) 60950, (CSA) C22.2 No. 60950, IEC 60950, EN 60950, AS/NZS 60950
Certification	CE (FCC) 15 (CFR 47) B ICES-003 B EN55022 B CISPR22 B AS/NZ 3548 B VCCI B EN55024 EN 50082-1 EN 61000-3-2 EN 61000-3-3
Compliance industry standards	IEEE 802.3, IEEE 802.3u, IEEE 802.1Q, IEEE 802.3af
Lines quantity	- lines
Phonebook capacity	- entries
Number of handles included	1 pc(s)

Weight and Dimensions

Weight	1600 g