EasyManuals Logo

Cisco 7941G Administration Guide

Cisco 7941G
292 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #61 background imageLoading...
Page #61 background image
Cisco Unified IP Phones and Different Protocols
The Cisco Unified IP Phones can operate with Skinny Client Control Protocol (SCCP) or Session Initiation
Protocol (SIP). You can convert a phone from using one protocol to using the other protocol.
Convert New Phone from SCCP to SIP
A new, unused phone is set for SCCP by default. To convert this phone to SIP, perform these steps:
Procedure
Step 1
Take one of these actions:
To autoregister the phone, set the Auto Registration Phone Protocol enterprise parameter in Cisco Unified
Communications Manager Administration to SIP.
To provision the phone by using the Bulk Administration Tool (BAT), choose the appropriate phone
model and choose SIP from BAT.
To provision the phone manually, make the appropriate changes for SIP on the Phone Configuration
window in Cisco Unified Communications Manager Administration.
For more information on Cisco Unified Communications Manager configuration, see Cisco Unified
Communications Manager Administration Guide. For more information on using BAT, see Cisco Unified
Communications Manager Bulk Administration Guide.
Step 2
If you are not using DHCP in your network, configure the network parameters for the phone.
Step 3
Save the configuration updates, click Apply Config, click OK in the Apply Configuration Information window,
and have the user power cycle the phone.
Related Topics
Network Settings, on page 57
In-Use Phone Protocol to Protocol Conversion
For information on how to convert an in-use phone from one protocol to the other, see the Cisco Unified
Communications Manager Administration Guide, Cisco Unified IP Phone Configuration chapter, Migrate
existing phone settings to another phone section.
Deploy Phone in SCCP and SIP Environment
To deploy Cisco Unified IP Phones in an environment that includes SCCP and SIP and in which the Cisco
Unified Communications Manager autoregistration parameter specifies SCCP, perform these general steps:
Cisco Unified IP Phone 7941G, 7941G-GE, 7942G, 7961G, 7961G-GE, and 7962G Administration Guide for Cisco Unified
Communications Manager 9.0 (SCCP and SIP)
41
Cisco Unified IP Phones and Your Network
Cisco Unified IP Phones and Different Protocols

Table of Contents

Other manuals for Cisco 7941G

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco 7941G and is the answer not in the manual?

Cisco 7941G Specifications

General IconGeneral
Keypad number of keys12
Touchscreen-
Display resolution320 x 222 pixels
SpeakerphoneYes
Voice codecsG.729a
BluetoothNo
Supported network protocolsDHCP, TFTP, SCCP, DSCP
Ethernet LAN (RJ-45) ports2
Input voltage48 V
Dimensions (WxDxH)266.7 x 152.4 x 203.2 mm
Storage temperature (T-T)-10 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Handset typeWired handset
Product typeIP Phone
Product colorGray
Safety(UL) 60950, (CSA) C22.2 No. 60950, IEC 60950, EN 60950, AS/NZS 60950
CertificationCE (FCC) 15 (CFR 47) B ICES-003 B EN55022 B CISPR22 B AS/NZ 3548 B VCCI B EN55024 EN 50082-1 EN 61000-3-2 EN 61000-3-3
Compliance industry standardsIEEE 802.3, IEEE 802.3u, IEEE 802.1Q, IEEE 802.3af
Lines quantity- lines
Phonebook capacity- entries
Number of handles included1 pc(s)
Weight and Dimensions IconWeight and Dimensions
Weight1600 g

Related product manuals