NAME: "subslot 0/0 transceiver 4", DESCR: "GE SX"
PID: GLC-SX-MMD , VID: 001 , SN: AGJ1825R4H0
NAME: "subslot 0/0 transceiver 5", DESCR: "GE SX"
PID: SFP-GE-S , VID: B , SN: FNS16270V1T
NAME: "subslot 0/0 transceiver 6", DESCR: "GE SX"
PID: FTRJ8519P1BNL-C5 , VID: , SN: FNS0928K33L
NAME: "subslot 0/0 transceiver 7", DESCR: "GE SX"
PID: GLC-SX-MMD , VID: A , SN: FNS170907MM
NAME: "SPA subslot 0/1", DESCR: "8-port Built-in 10-Gigabit Ethernet Port Adapter"
PID: BUILT-IN-EPA-8x10G, VID: N/A , SN: JAE87654321
NAME: "subslot 0/1 transceiver 0", DESCR: "SFP+ 10GBASE-SR"
PID: SFP-10G-SR , VID: A , SN: FNS17241B6A
NAME: "subslot 0/1 transceiver 2", DESCR: "SFP+ 10GBASE-SR"
PID: SFP-10G-SR , VID: A , SN: SPC144701S6
NAME: "subslot 0/1 transceiver 4", DESCR: "SFP+ 10GBASE-SR"
PID: SFP-10G-SR , VID: G4.1 , SN: AVD1828A6PH
NAME: "subslot 0/1 transceiver 6", DESCR: "SFP+ 10GBASE-SR"
PID: SFP-10G-SR , VID: A , SN: FNS16190YXT
NAME: "module R0", DESCR: "Cisco ASR1002-HX Route Processor"
PID: ASR1002-HX , VID: V00 , SN: JAE1931098U
NAME: "module F0", DESCR: "Cisco ASR1002-HX Embedded Services Processor"
PID: ASR1002-HX , VID: , SN:
Router#
show platform Command
The show platform command displays platform information.
The following is sample output from the show platform command:
Router# show platform
Chassis type: ASR1001-HX
Slot Type State Insert time (ago)
--------- ------------------- --------------------- -----------------
0 ASR1001-HX ok 00:03:19
0/0 BUILT-IN-EPA-8x1G ok 00:02:08
0/1 BUILT-IN-8X10G/1G ok 00:02:10
R0 ASR1001-HX ok 00:03:19
R0/0 ok, active 00:03:19
R0/1 ok, standby 00:01:42
F0 ASR1001-HX ok, active 00:03:19
P0 ASR1000X-AC-750W ok 00:03:00
P1 ASR1000X-AC-750W ok 00:03:00
P2 ASR1001HX-FAN ok l 00:03:00
Slot CPLD Version Firmware Version
--------- ------------------- ---------------------------------------
0 15081816 16.2(2r)
R0 15081816 16.2(2r)
F0 15081816 16.2(2r)
Router#
Cisco ASR 1001-HX Router and Cisco ASR 1002-HX Router Hardware Installation Guide
91
Power Up and Initial Configuration
Reporting Functions