Cisco ASR1006 - ASR 1006 Modular Expansion Base User Manual

Configuring Call Home
Message Contents
55
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide
*Dec 3 12:17:17.905 IST: %LINEPROTO-5-UPDOWN: Line protocol on Interface POS2/3/0,
changed state to up
*Dec 3 12:22:01.574 IST: %IP-4-DUPADDR: Duplicate address 172.27.55.233 on
GigabitEt
hernet0, sourced by 001a.3044.1ec0
*Dec 3 12:23:47.613 IST: %SYS-5-CONFIG_I: Configured from console by console
*Dec 3 12:24:37.134 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console
*Dec 3 12:25:34.356 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has
failed. E
rror code = 0x1 (DIAG_FAILURE)
*Dec 3 12:25:39.459 IST: %DIAG-3-TEST_FAIL: slot R0: TestErrorCounterMonitor{ID=1} has
failed. E
rror code = 0x1 (DIAG_FAILURE)
*Dec 3 12:25:54.405 IST: %SYS-5-CONFIG_I: Configured from console by console
*Dec 3 12:26:02.319 IST: %CLEAR-5-COUNTERS: Clear counter on all interfaces by console
*Dec 3 12:28:56.057 IST: %SYS-5-CONFIG_I: Configured from console by console
mcp-6ru-3#]]></aml-block:Data>
</aml-block:Attachment>
<aml-block:Attachment type="inline">
<aml-block:Name>show inventory</aml-block:Name>
<aml-block:Data encoding="plain">
<![CDATA[NAME: "Chassis", DESCR: "Cisco ASR1006 Chassis"
PID: ASR1006 , VID: V00, SN: FOX105101DH
NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 10"
PID: MCP-CC , VID: V00, SN: JAB1104064W
NAME: "SPA subslot 0/2", DESCR: "8-port OC3/STM1 POS Shared Port Adapter"
PID: SPA-8XOC3-POS , VID: V01, SN: JAE1236TSW0
NAME: "subslot 0/2 transceiver 0", DESCR: "OC3 SR-1/STM1 MM"
PID: SFP-OC3-MM , VID: A , SN: OCP12231628
NAME: "module 1", DESCR: "Cisco ASR1000 SPA Interface Processor 10"
PID: MCP-CC , VID: V00, SN: JAB1104062X
NAME: "SPA subslot 1/3", DESCR: "4-port OC3/STM1 POS Shared Port Adapter"
PID: SPA-4XOC3-POS , VID: V01, SN: JAB085202QU
NAME: "subslot 1/3 transceiver 0", DESCR: "OC3 SR-1/STM1 MM"
PID: SFP-OC3-MM , VID: A , SN: OCP12310174
NAME: "module 2", DESCR: "Cisco ASR1000 SPA Interface Processor 10"
PID: ASR1000-SIP10 , VID: V00, SN: JAB113701L9
NAME: "SPA subslot 2/3", DESCR: "1-port OC12/STM4 POS Shared Port Adapter"
PID: SPA-1XOC12-POS , VID: V01, SN: JAE1236U41L
NAME: "subslot 2/3 transceiver 0", DESCR: "OC12 SR-1/STM4 MM"
PID: SFP-OC12-MM , VID: A , SN: OCP10100281
NAME: "module R0", DESCR: "Cisco ASR1000 Route Processor 1"
PID: ASR1000-RP1 , VID: V00, SN: JAB11110181
NAME: "module R1", DESCR: "Cisco ASR1000 Route Processor 1"
PID: ASR1000-RP1 , VID: V00, SN: JAB1111016K
NAME: "module F0", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps"
PID: ASR1000-ESP10 , VID: V00, SN: JAB111801ZX
NAME: "module F1", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps"
PID: ASR1000-ESP10 , VID: V00, SN: JAB111101AP
NAME: "Power Supply Module 0", DESCR: "Cisco ASR1006 AC Power Supply"
PID: TBD000000000000000, VID: +^A , SN: ART1114Q00F
NAME: "Fan Module 1", DESCR: "Cisco ASR1006 Fan Module"

Cisco ASR1006 - ASR 1006 Modular Expansion Base Specifications

General

Rack Units	6U
Form Factor	Rack-mountable
Operating Temperature	32 to 104°F (0 to 40°C)
Product Type	Router
Slots	6
Redundancy	Redundant Power Supply Supported
Maximum Throughput	100 Gbps
Dimensions	17.5" Width
Weight	Approximately 130 lbs (59 kg)
Interfaces/Ports	Varies by installed modules
Memory	4 GB
Storage Temperature	-40°F to 158°F (-40°C to 70°C)
Relative Humidity	5% to 95% (noncondensing)
Compliance	CE, UL