Colop e-mark create - Fig. 1: Safety Instructions on the Underside of the E-Mark Create

60 pages

Save Page as PDF

To Next Page

To Previous Page

e-mark create marking device Chapter 2 Safety

CODI Standard 1.0 15/60

Operating and Maintenance Manual

Fig. 1: Safety instructions on the underside of the e-mark create

Main Page

Table of Contents2
Introduction6
Legal Details6
Liability7
Intended Use7
Principle8
Safety9
Signal Words Used in Safety Notices9
Symbols Used in Safety Notices10
Residual Hazards11
General Safety Instructions and Regulations14
Safety Notices on the Product14
Fig. 1: Safety Instructions on the Underside of the E-Mark Create15
Description16
Scope of Supply16
Fig. 2: Package Content16
Components17
Fig. 3: E-Mark Create Parts17
Layout18
Fig. 4: Marking Device Assembly Underside18
Fig. 5: Docking Station Assembly Top Section and Underside19
Technical Specifications and Dimensions20
Operating Systems21
Initial Operation21
Transport and Unpacking21
Fig. 6: Packaging22
Assembly and Switching on23
Fig. 7: Opening and Removing the Cover23
Fig. 8: Opening the Battery Compartment and Remove Battery23
Fig. 9: Battery Contact Insulating Tape24
Fig. 10: Opening the Sliding Panel24
Fig. 11: Ink Cartridge25
Fig. 12: Insert Ink Cartridge25
Fig. 13: Close Lower Flap Cover25
Fig. 14: Insert Battery26
Software27
Wifi Connection27
Fig. 15: Example Test Imprint with SSID and Password27
Operation28
Image Transfer28
Printing29
Fig. 16: On/Off Switch29
Fig. 17: Remove E-Mark Create from the Docking Station30
Fig. 18: Printing from Left to Right30
Fig. 19: Printing from Right to Left30
Fig. 20: Multi-Line Imprint Procedure31
Fig. 21: Place into Docking Station31
Light Guide and Symbols33
Fig. 22: Light Guide33
Fig. 23: Light Guide Directions33
Automatic Cleaning Cycle37
Fig. 24: Colour Sample Released by Automatic Print Head Cleaning37
Fig. 25: Do Not Direct Towards Eyes, Face or Skin. Light Irritation Possible37
Manual Cleaning Cycle38
Fig. 26: Slide out Print Head Wiper38
Fig. 27: Clean Print Head with Wiper38
Fig. 28: Clean Print Head with Damp Cloth39
Software40
Fig. 29: Software Wizard - Welcome Page40
Fig. 30: Software Wizard - WIFI Information40
Fig. 31: Software Wizard - Connection to E-Mark Create41
Fig. 32: Software Wizard - Test Imprint41
Fig. 33: "My Imprints" Page42
Fig. 34: E-Mark Connect Page42
Wifi Connection43
Fig. 35: Example Image of WIFI Connection in the Settings of the Mobile Device43
Usb Cable Connection44
Storage44
Fig. 36: USB Connection44
Maintenance45
Charging the Battery45
Fig. 37: Power Plug45
Fig. 38: Charge Battery46
Changing the Ink Cartridge47
Fig. 39: Open and Remove Cover48
Fig. 40: Battery48
Fig. 41: Open Battery Compartment48
Fig. 42: Opening the Sliding Panel49
Fig. 43: Sliding Panel Open49
Fig. 44: Pull out Ink Cartridge50
Fig. 45: Ink Cartridge50
Fig. 46: Insert Ink Cartridge50
Fig. 47: Close Lower Flap Cover51
Fig. 48: Insert Battery51
Fig. 49: Cover Closed51
Cleaning52
Fig. 50: Put into Docking Station52
Troubleshooting53
Reset56
Repairs & Return56
Fig. 51: Opening for Device Reset56
Fig. 52: Cover the Contacts of the Battery56
Spare and Wear Parts57
Shutdown and Disposal58
Fig. 53: Remove Covers58
Fig. 54: Remove Screws59
Fig. 55: Open the Housing59
Appendix60

Colop e-mark create - Fig. 1: Safety Instructions on the Underside of the E-Mark Create

Table of Contents