D-Link DSR-1000 - Page 249

249
付録D ログメッセージ
ログメッセージ 緊急度 ログメッセージ 緊急度
%s: unable to attach hardware; HAL status %u, DEBUG UMI proto registration failed %d,ret ERROR
%s: HAL ABI msmatch; DEBUG AF_UMI registration failed %d,ret ERROR
%s: Warning, using only %u entries in %u key cache, DEBUG umi initialization failed %d,ret ERROR
unable to setup a beacon xmit queue! DEBUG kernel UMI registration failed! ERROR
unable to setup CAB xmit queue! DEBUG ./Logs_kernel.txt:447:KERN_ERR ERROR
unable to setup xmit queue for BE tra󱐰c! DEBUG ERROR msm not found properly %d, len %d, msm, ERROR
%s DFS attach failed, __func__ DEBUG ModExp returned Error ERROR
%s: Invalid interface id = %u, __func__, if_id DEBUG ModExp returned Error ERROR
%s:grppoll Buf allocation failed ,__func__ DEBUG %s: 0x%p len %u, tag, p, (unsigned int)len ERROR
%s: unable to start recv logic, DEBUG %03d:, i ERROR
%s: Invalid interface id = %u, __func__, if_id DEBUG %02x, ((unsigned char *)p)[i] ERROR
%s: unable to allocate channel table, __func__ DEBUG mic check failed ERROR
%s: Tx Antenna Switch. Do internal reset., __func__ DEBUG %s: 0x%p len %u, tag, p, (unsigned int)len ERROR
Radar found on channel %d (%d MHz), DEBUG %03d:, i ERROR
End of DFS wait period DEBUG %02x, ((unsigned char *)p)[i] ERROR
%s error allocating beacon, __func__ DEBUG mic check failed ERROR
failed to allocate UAPSD QoS NULL tx descriptors: %d, error DEBUG [%s] Wrong parameters, __func__ ERROR
failed to allocate UAPSD QoS NULL wbuf DEBUG [%s] Wrong Key length, __func__ ERROR
%s: unable to allocate channel table, __func__ DEBUG [%s] Wrong parameters, __func__ ERROR
%s: unable to update h/w beacon queue parameters, DEBUG [%s] Wrong Key length, __func__ ERROR
ALREADY ACTIVATED DEBUG [%s] Wrong parameters, __func__ ERROR
%s: missed %u consecutive beacons, DEBUG [%s] Wrong Key length, __func__ ERROR
%s: busy times: rx_clear=%d, rx_frame=%d, tx_frame=%d, __
func__, rx_clear, rx_frame, tx_frame
DEBUG [%s] Wrong parameters, __func__ ERROR
%s: unable to obtain busy times, __func__ DEBUG [%s] Wrong Key length, __func__ ERROR
%s: beacon is o󱐰cially stuck, DEBUG [%s]: Wrong parameters, __func__ ERROR
Busy environment detected DEBUG [%s] Wrong Key Length %d, __func__, des_key_len ERROR
Inteference detected DEBUG [%s] Wrong parameters %d, __func__, des_key_len ERROR
rx_clear=%d, rx_frame=%d, tx_frame=%d, DEBUG [%s] Wrong Key Length %d, __func__, des_key_len ERROR
%s: resume beacon xmit after %u misses, DEBUG [%s] Wrong parameters, __func__ ERROR
%s: stuck beacon; resetting (bmiss count %u), DEBUG [%s] Wrong Key Length, __func__ ERROR
EMPTY QUEUE DEBUG [%s] Wrong parameters, __func__ ERROR
SWRInfo: seqno %d isswRetry %d retryCnt %d,wh ? (*(u_int16_
t *)&wh- >i_seq[0]) >> 4 : 0, bf->bf_isswretry,bf- >bf_swretries
DEBUG [%s] Wrong Key Length, __func__ ERROR
Bu󱐯er #%08X --> Next#%08X Prev#%08X Last#%08X,bf,
TAILQ_NEXT(bf,bf_list),
DEBUG [%s] Wrong parameters, __func__ ERROR
Stas#%08X ag#%08X Node#%08X, bf->bf_status, bf->bf_
ags, bf->bf_node
DEBUG [%s] Wrong parameters, __func__ ERROR
Descr #%08X --> Next#%08X Data#%08X Ctl0#%08X
Ctl1#%08X, bf- >bf_daddr, ds->ds_link, ds->ds_data, ds->ds_
ctl0, ds->ds_ctl1
DEBUG [%s] Wrong parameters, __func__ ERROR
Ctl2#%08X Ctl3#%08X Sta0#%08X Sta1#%08X,ds->ds_hw[0],
ds->ds_hw[1], lastds->ds_hw[2], lastds- >ds_hw[3]
DEBUG [%s] Wrong parameters, __func__ ERROR
Error entering wow mode DEBUG device name=%s not found, pReq- >ifName ERROR
Wakingup due to wow signal DEBUG unable to register KIFDEV to UMI ERROR
%s, wowStatus = 0x%x, __func__, wowStatus DEBUG ERROR: %s: Timeout at page %#0x addr %#0x ERROR
Pattern added already DEBUG ERROR: %s: Timeout at page %#0x addr %#0x ERROR
Error : All the %d pattern are in use. Cannot add a new
pattern , MAX_NUM_PATTERN
DEBUG Invalid IOCTL %#08x, cmd ERROR
Pattern added to entry %d ,i DEBUG %s: unable to register device, dev- >name ERROR
Remove wake up pattern DEBUG ath_pci: 32-bit DMA not available ERROR
mask = %p pat = %p ,maskBytes,patternBytes DEBUG ath_pci: cannot reserve PCI memory region ERROR
mask = %x pat = %x ,(u_int32_t)maskBytes, (u_int32_t)
patternBytes
DEBUG ath_pci: cannot remap PCI memory region) ; ERROR
Pattern Removed from entry %d ,i DEBUG ath_pci: no memory for device state ERROR