D-Link DSR-1000 - Page 250

250
付録D ログメッセージ
ログメッセージ 緊急度 ログメッセージ 緊急度
Error : Pattern not found DEBUG %s: unable to register device, dev- >name ERROR
PPM STATE ILLEGAL %x %x, forcePpmStateCur, afp->forceState DEBUG ath_dev_probe: no memory for device state ERROR
FORCE_PPM %4d %6.6x %8.8x %8.8x %8.8x %3.3x %4.4x, DEBUG %s: no memory for device state, __func__ ERROR
failed to allocate tx descriptors: %d, error DEBUG kernel MIBCTL registration failed! ERROR
failed to allocate beacon descripotrs: %d, error DEBUG Bad ioctl command ERROR
failed to allocate UAPSD descripotrs: %d, error DEBUG WpsMod: Failed to congure gpio pin ERROR
hal qnum %u out of range, max %u!, DEBUG WpsMod: Failed to register interrupt handler ERROR
HAL AC %u out of range, max %zu!, DEBUG registering char device failed ERROR
HAL AC %u out of range, max %zu!, DEBUG unregistering char device failed ERROR
%s: unable to update hardware queue %u!, DEBUG %s:%d - ERROR: non-NULL node pointer in %p, %p<%s>! ERROR
Multicast Q: DEBUG %s:%d - ERROR: non-NULL node pointer in %p, %p<%s>! ERROR
%p , buf DEBUG can't alloc name %s, name ERROR
buf ags - 0x%08x --------- , buf- >bf_ags DEBUG %s: unable to register device, dev- >name ERROR
buf status - 0x%08x, buf->bf_status DEBUG failed to automatically load module: %s; \ ERROR
# frames in aggr - %d, length of aggregate - %d, length of
frame - %d, sequence number - %d, tidno - %d,
DEBUG Unable to load needed module: %s; no support for \ ERROR
isdata: %d isaggr: %d isampdu: %d ht: %d isretried: %d
isxretried: %d shpreamble: %d isbar: %d ispspoll: %d
aggrburst: %d calcairtime: %d qosnulleosp: %d,
DEBUG Module \%s\ is not known, buf ERROR
%p: 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x 0x%08x,
DEBUG Error loading module \%s\, buf ERROR
0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x 0x%08x
0x%08x 0x%08x 0x%08x,
DEBUG Module \%s\ failed to initialize, buf ERROR
0x%08x 0x%08x 0x%08x 0x%08x, DEBUG ath_pci: 32-bit DMA not available ERROR
sc_txq[%d] : , i DEBUG ath_pci: cannot reserve PCI memory region ERROR
tid %p pause %d : , tid, tid->paused DEBUG ath_pci: cannot remap PCI memory region) ; ERROR
%d: %p , j, tid->tx_buf[j] DEBUG ath_pci: no memory for device state ERROR
%p , buf DEBUG %s: unable to attach hardware: '%s' (HAL status %u), ERROR
axq_q: DEBUG %s: HAL ABI mismatch; ERROR
%s: unable to reset hardware; hal status %u, __func__, status DEBUG %s: failed to allocate descriptors: %d, ERROR
****ASSERTION HIT**** DEBUG %s: unable to setup a beacon xmit queue!, ERROR
MacAddr=%s, DEBUG %s: unable to setup CAB xmit queue!, ERROR
TxBufIdx=%d, i DEBUG %s: unable to setup xmit queue for %s tra󱐰c!, ERROR
Tid=%d, tidno DEBUG %s: unable to register device, dev- >name ERROR
AthBuf=%p, tid->tx_buf[i] DEBUG %s: autocreation of VAP failed: %d, ERROR
%s: unable to reset hardware; hal status %u, DEBUG ath_dev_probe: no memory for device state ERROR
%s: unable to reset hardware; hal status %u, DEBUG kdot11RogueAPEnable called with NULL argument. ERROR
%s: unable to start recv logic, DEBUG kdot11RogueAPEnable: can not add more interfaces ERROR
_fmt, __VA_ARGS__ \ DEBUG kdot11RogueAPGetState called with NULL argument. ERROR
sample_pri=%d is a multiple of refpri=%d, sample_pri, refpri DEBUG kdot11RogueAPDisable called with NULL argument. ERROR
===========ft- >ft_numlters=%u===========, ft-
>ft_numlters
DEBUG %s: SKB does not exist., __FUNCTION__ ERROR
lter[%d] lterID = %d rf_numpulses=%u; rf->rf_minpri=%u; rf-
>rf_maxpri=%u; rf->rf_threshold=%u; rf- >rf_lterlen=%u; rf-
>rf_mindur=%u; rf- >rf_maxdur=%u,j, rf->rf_pulseid,
DEBUG %s: recvd invalid skb ERROR
NOL DEBUG unable to register KIFDEV to UMI ERROR
WARNING!!! 10 minute CAC period as channel is a weather
radar channel
DEBUG The system is going to factory defaults........!!! CRITICAL
%s disable detects, __func__ DEBUG %s, msg CRITICAL
%s enable detects, __func__ DEBUG %02x, *(data + i) CRITICAL
%s disable FFT val=0x%x , __func__, val DEBUG Inside crypt_open in driver ###### CRITICAL
%s enable FFT val=0x%x , __func__, val DEBUG Inside crypt_release in driver ###### CRITICAL
%s debug level now = 0x%x , __func__, dfs_debug_level DEBUG Inside crypt_init module in driver @@@@@@@@ CRITICAL
RateTable:%d, maxvalidrate:%d, ratemax:%d, pRc-
>rateTableSize,k,pRc- >rateMaxPhy
DEBUG Inside crypt_cleanup module in driver @@@@@@@@ CRITICAL