To Next PageTo Next PageWhy is the power indicator blinking red on my Denon Stereo Receiver in intervals of approximately 2 seconds?
If the power indicator on your Denon Stereo Receiver blinks red every 2 seconds, it indicates the unit's internal temperature has risen. Turn off the power and allow the unit to cool down before turning it back on. Consider reinstalling the unit in a location with better ventilation.
How to troubleshoot reception fails on Denon Stereo Receiver?
If you're experiencing poor reception, noise, or distortion on your Denon Stereo Receiver, try the following: * Adjust the antenna's orientation or position. * Separate the AM loop antenna from the unit. * Consider using an FM outdoor antenna. * Keep the antenna separate from other connection cables.
What to do if iPod cannot be played on Denon Stereo Receiver?
If your iPod isn't playing on your Denon Stereo Receiver, try the following: * Check the iPod connections. * Plug the control dock for iPod’s AC adapter into a power outlet. * Switch the input source to “DOCK.”
What does “Not Support” displayed on Denon AVR-1611 Stereo Receiver mean?
If “Not Support” is displayed on your Denon Stereo Receiver, it could mean: * The connected iPod is not compatible. Ensure the iPod you are connecting is a compatible model. * The software version of the connected iPod is outdated. Update to the latest version.
What to do after turning on the power, the power indicator is blinking red in intervals of approximately 0.5 seconds on Denon Stereo Receiver?
This indicates that the unit amplifier circuit has failed. Turn off the power and please contact the DENON service adviser.
Why is there no audio output with HDMI connection on my Denon AVR-1611 Stereo Receiver?
If there is no audio output with HDMI connection on your Denon Stereo Receiver, check the connection of the HDMI connectors. When outputting HDMI audio from the speakers, set “HDMI Audio Out” on the menu to “Amp”. When outputting HDMI audio from a TV, set “HDMI Audio Out” on the menu to “TV".
How to troubleshoot no sound from the subwoofer on a Denon Receiver?
If your Denon Receiver's subwoofer isn't producing sound, try the following: * Check the subwoofer connections. * Make sure the subwoofer is powered on. * In the menu, set "Speaker Config." – "Subwoofer" to "Yes." * Note that if "Front" and "Center" are set to “Large” and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
Why is the power indicator blinking red rapidly on my Denon Receiver?
If the power indicator on your Denon Receiver is blinking red every 0.5 seconds, ensure you are using speakers with the specified impedance. Also, check the speaker cables for shorts and firmly twist the core wire before reconnecting them to the speaker terminal.
Why is there no audio output from my Denon Receiver?
If no audio is coming from your Denon Receiver, there are several things to check: * Make sure all device connections are secure. * Verify the speaker connections. * Ensure the audio device is powered on. * Adjust the master volume. * Deactivate mute mode. * Select the correct input source and mode. * If headphones are connected, disconnect them, as this will prevent sound from the speakers or PRE OUT connectors.
How to fix a Denon Receiver that does not turn on?
If your Denon Receiver isn't powering on, it might be due to the protection circuit being active. To resolve this, disconnect the power plug from the electrical outlet, wait 5 to 10 seconds, and then plug it back in.
General| Impedance | 6 Ω |
|---|---|
| Frequency range | 10 - 100000 Hz |
| Audio output channels | 5.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 98 dB |
| Total Harmonic Distortion (THD) | 0.7 % |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| Radio Data System (RDS) | Yes |
| Audio system | Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, DTS-HD, DTS 96/24 |
| Output power | 110 W |
| Dimensions (WxDxH) | 434 x 381 x 171 mm |
| Power requirements | AC 230, 50 Hz |
| HDMI ports quantity | 5 |
| I/O ports | 1 x Component 3 x Composite (Video) 5 x Analogue Audio (Tuner included) 1 x Composite Monitor 1 x Microphone Port 1 x Dock Control Port 1 x FM Tuner Antenna 1 x AM Tuner Antenna |
| Connectivity technology | Wired |
| Digital audio optical in | 1 |
| Product color | Black |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 360 W |
Weight and Dimensions| Weight | 9200 g |
|---|
Essential safety guidelines for operating the apparatus, including warnings and instructions.
Compliance information for US customers regarding radio frequency and interference.
Important warnings regarding temperature, handling, environment, and component care.
Guidelines for safe and proper installation of the unit, including ventilation and placement.
Details on discrete amplifiers, HDMI 1.4a support, and dock connectivity for iPod.
Highlights Dolby Pro Logic IIz, video upconverting, and user-friendly on-screen display.
Steps for physical setup and connecting speakers and sources like TV and Blu-ray.
Procedures for powering the unit and configuring speakers via Audyssey Auto Setup.
Instructions for playing discs and enjoying surround sound.
Guide to connecting various media and external devices like TVs and players.
How to select sources, adjust volume, and play media.
Choosing surround sound modes for optimal audio experience.
Methods for installing and connecting speakers beyond 5.1 channels.
Using features like HDMI control, sleep timer, and quick select.
Configuring audio, input, and system preferences via menus.
Controlling connected devices and registering preset codes.
Overview of front panel, rear panel, and remote control components.
Resolving common audio, video, and system operation issues.
Detailed specifications including audio, video, and tuner sections.
Definitions of technical terms and features used in the manual.
