To Next PageTo Next PageWhy is there no sound from the surround back speaker on my Denon AVR-1611?
If no sound is produced from surround back speaker on your Denon Stereo Receiver, set “Pre Assign” on the menu to “Normal". Set “Speaker Config.” – “S.Back” on the menu to something other than “None". Set “Surround Parameter” – “S.Back” on the menu to something other than “OFF". Set the surround mode to something other than “STEREO".
Why is my Denon AVR-1611 not outputting sound to the subwoofer?
If no sound is produced from the subwoofer connected to your Denon Stereo Receiver, check the subwoofer connections and ensure the subwoofer’s power is turned on. Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”. If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
Why is Dolby TrueHD/DTS-HD audio not working on my Denon AVR-1611 Stereo Receiver?
If Dolby TrueHD, DTS-HD, or Dolby Digital Plus audio is not output from your Denon Stereo Receiver, make HDMI connections.
How do I improve radio reception on my Denon AVR-1611?
If reception fails, or there is a lot of noise or distortion on your Denon Stereo Receiver, change the antenna orientation or position. Separate the AM loop antenna from the unit. Use an FM outdoor antenna and separate the antenna from other connection cables.
What to do if no audio is output from Denon AVR-1611 Stereo Receiver?
If you're not getting any sound from your Denon Stereo Receiver, here are a few things to check: * Make sure all your device connections are secure. * Verify the speaker connections are correct. * Ensure the audio device is powered on. * Adjust the master volume. * Cancel mute mode. * Select the appropriate input source and input mode. * Disconnect any connected headphones.
How to fix no audio output with HDMI connection on Denon AVR-1611?
If you're experiencing no audio output with an HDMI connection on your Denon Stereo Receiver: * Check the connection of the HDMI connectors. * To output HDMI audio from the speakers, set “HDMI Audio Out” on the menu to “Amp.” * To output HDMI audio from a TV, set “HDMI Audio Out” on the menu to “TV.”
Why is there no sound from surround back speaker on my Denon Stereo Receiver?
If you're not getting sound from the surround back speaker on your Denon Stereo Receiver, check these settings in the menu: * Set “Amp Assign” to “Normal.” * Set “Speaker Config.” – “S.Back” to something other than “None.” * Set “Surround Parameter” – “S.Back” to something other than “OFF.” * Ensure the surround mode is not set to “STEREO.”
How to resolve no sound from front height speaker on Denon Stereo Receiver?
If there is no sound from the front height speaker of your Denon Stereo Receiver, ensure that: * “Surround Parameter” – “Front Height” on the menu is set to “ON.” * “Amp Assign” on the menu is set to “Front Height.” * “Speaker Config.” – “Surround” on the menu is set to something other than “None.”
How to resolve no sound from subwoofer on Denon AVR-1611 Stereo Receiver?
If you're not getting sound from the subwoofer on your Denon Stereo Receiver: * Check the subwoofer connections. * Make sure the subwoofer is powered on. * Set “Speaker Config.” – “Subwoofer” on the menu to “Yes.” * Note: If “Front” and “Center” for “Speaker Config.” are set to “Large”, and “Subwoofer Mode” is set to “LFE”, no sound may be output from the subwoofers, depending on the input signal or selected surround mode.
General| Impedance | 6 Ω |
|---|---|
| Frequency range | 10 - 100000 Hz |
| Audio output channels | 5.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Signal-to-Noise Ratio (SNR) | 98 dB |
| Total Harmonic Distortion (THD) | 0.7 % |
| AM band range | 522 - 1611 kHz |
| FM band range | 87.5 - 108 MHz |
| Radio Data System (RDS) | Yes |
| Audio system | Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, DTS-HD, DTS 96/24 |
| Output power | 110 W |
| Dimensions (WxDxH) | 434 x 381 x 171 mm |
| Power requirements | AC 230, 50 Hz |
| HDMI ports quantity | 5 |
| I/O ports | 1 x Component 3 x Composite (Video) 5 x Analogue Audio (Tuner included) 1 x Composite Monitor 1 x Microphone Port 1 x Dock Control Port 1 x FM Tuner Antenna 1 x AM Tuner Antenna |
| Connectivity technology | Wired |
| Digital audio optical in | 1 |
| Product color | Black |
| Power consumption (standby) | 0.1 W |
| Power consumption (typical) | 360 W |
Weight and Dimensions| Weight | 9200 g |
|---|
Essential safety guidelines for operating the apparatus, including warnings and instructions.
Compliance information for US customers regarding radio frequency and interference.
Important warnings regarding temperature, handling, environment, and component care.
Guidelines for safe and proper installation of the unit, including ventilation and placement.
Details on discrete amplifiers, HDMI 1.4a support, and dock connectivity for iPod.
Highlights Dolby Pro Logic IIz, video upconverting, and user-friendly on-screen display.
Steps for physical setup and connecting speakers and sources like TV and Blu-ray.
Procedures for powering the unit and configuring speakers via Audyssey Auto Setup.
Instructions for playing discs and enjoying surround sound.
Guide to connecting various media and external devices like TVs and players.
How to select sources, adjust volume, and play media.
Choosing surround sound modes for optimal audio experience.
Methods for installing and connecting speakers beyond 5.1 channels.
Using features like HDMI control, sleep timer, and quick select.
Configuring audio, input, and system preferences via menus.
Controlling connected devices and registering preset codes.
Overview of front panel, rear panel, and remote control components.
Resolving common audio, video, and system operation issues.
Detailed specifications including audio, video, and tuner sections.
Definitions of technical terms and features used in the manual.
