To Next PageTo Next PageHow to fix no sound from center speaker on Denon Stereo Receiver?
If no sound is being produced from the center speaker on your Denon Stereo Receiver, and you are playing a monaural source (monitor, AM station, etc.) in “STANDARD” mode, set the mode to something other than “STANDARD.”
Why is there no sound from my Denon Stereo Receiver subwoofer?
If your subwoofer isn't producing sound, first ensure that the subwoofer's power is turned on. Check that the “Subwoofer” setting at “Speaker configuration” is set to “Yes.” Verify that the subwoofer is properly connected. Finally, adjust the subwoofer’s volume to an appropriate level, as it may be turned off.
How to fix Denon Stereo Receiver no sound from speakers?
If no sound is coming from the speakers connected to your Denon Stereo Receiver, there are several things to check: * Ensure that all connections with the input devices and speaker cables are properly connected. * Verify that the device you want to play and the set input source match. * Adjust the master volume to an appropriate level, as it may be turned too low. * Cancel the mute mode if it is set. * Disconnect any connected headphones. * Select an input source for which the digital input setting has been made, if no digital signals are being input. * Set the input mode to match the connectors to which the digital inputs are assigned.
How to fix the on-screen display not appearing on my Denon Receiver?
If the on-screen display does not appear on your Denon Receiver, it means that the format of the GUI and TV (PAL or NTSC) do not match. You should match the format of the GUI and TV.
Why is no sound produced from the subwoofer on my Denon Receiver?
If you're not getting any sound from the subwoofer connected to your Denon Receiver, there are several things to check: 1. Ensure the subwoofer’s power is turned on. 2. Verify that the “Subwoofer” setting at “Speaker Configuration” is set to “Yes.” 3. Check the connections to make sure the subwoofer is properly connected. 4. Adjust the subwoofer’s volume to an appropriate level, ensuring it’s not turned off.
Why is no sound produced from the surround back speaker on my Denon Receiver?
If you're not hearing any sound from the surround back speaker on your Denon Receiver, there are a few things to check. First, make sure the surround back speaker setting is not set to “None”; if it is, change it to something other than “None.” Second, ensure that the surround mode is set to a mode for 6.1- or 7.1-channel playback by selecting a surround playback mode. Finally, verify that the surround back speaker’s power amplifier is not assigned to a different channel, and change the setting if necessary.
Why is no sound produced from the surround speakers on my Denon Receiver?
If you're not getting any sound from the surround speakers on your Denon Receiver, it could be because the surround mode is set to “STEREO”, “DIRECT” or “PURE DIRECT”. To fix this, set the receiver to a surround playback mode. Also, check if the surround speaker’s power amplifier is assigned to a different channel and change the setting if necessary.
Why is no sound produced from the center speaker on my Denon Receiver?
If you're not hearing any sound from the center speaker on your Denon Receiver, and you are playing a monaural source (such as TV or AM radio) in STANDARD mode, try setting the mode to something other than “STANDARD.”
Why is the display off on my Denon Receiver?
If your Denon Receiver's display is off, it could be due to one of two reasons. First, the “Dimmer” setting might be set to “OFF”; in this case, change it to something other than “OFF.” Second, the PURE DIRECT mode might be enabled; if so, set a surround mode other than the PURE DIRECT mode.
How to fix HDMI audio signals not outputting from speakers on Denon Receiver?
If your Denon Receiver isn't outputting HDMI audio signals from the speakers, the “Manual Setup” – “HDMI Setup” – “Audio” setting might be set to “TV”. Change this setting to “Amp.”
General| Number of Channels | 7.1 |
|---|---|
| HDMI Inputs | 4 |
| HDMI Outputs | 2 |
| Networking | Ethernet, Wi-Fi |
| Multi-room Zones | 3 |
| THX Certified | No |
| Frequency Response | 10 Hz - 100 kHz (+1, -3 dB) |
| Total Harmonic Distortion | 0.05% |
| Input Sensitivity/Impedance | 200 mV / 47 kOhms |
| Signal-to-Noise Ratio | 102 dB |
| HDMI Version | 1.3a |
| Dolby Technologies | Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Pro Logic IIx |
| DTS Technologies | DTS, DTS-ES, DTS 96/24, DTS-HD Master Audio |
| Tuner Frequency Range | FM: 87.5 MHz - 108.0 MHz, AM: 522 kHz - 1611 kHz |
| Audio Inputs/Outputs | Analog, Digital Coaxial, Digital Optical, HDMI |
Official compliance statements for R&TTE Directive 1999/5/EC in various languages.
Explanation of buttons, indicators, and connectors on the front panel.
Diagrams and button functions for the primary and secondary remotes.
Diagrams and table detailing speaker setup options for different channel configurations.
Step-by-step guide for connecting speaker wires to terminals.
Information on the protection circuit activation and troubleshooting.
Explains HDMI version, Deep Color, and HDCP compatibility for digital content playback.
Details on network requirements and setting up a wired connection.
Guidance on setting up a wireless network connection.
How to connect amplifiers for multi-zone audio output.
Connecting external controllers via RS-232C or trigger jacks.
Steps to connect the microphone and identify the main listening position for calibration.
Setting up configuration and the first steps of speaker detection and measurement.
Steps for analyzing measurements, verifying results, and saving settings.
Resolving issues with microphone detection, noise, and phase errors.
Selecting Room EQ, Direct Mode, Mic Type, and checking parameters.
Adjusting speaker size, subwoofer mode, and distance to listening position.
Setting speaker channel levels and crossover frequency for subwoofer.
Setting crossover frequency and choosing surround speakers for different modes.
Adjusting i/p Scaler, Resolution, Progressive Mode, Aspect, Color Space, RGB Range.
Configuring HDMI audio output, Auto Lip Sync, and monitor output settings.
Speaker settings for EXT. IN, 2-channel modes, and downmix options.
Settings for automatic surround mode memorization and manual equalizer adjustments.
Steps to configure a wired network connection using DHCP or manual IP settings.
Steps to configure a wireless network connection via search or manual settings.
How to search for networks, set SSID, and encryption methods.
Configuring IP address manually and setting up proxy servers for network access.
Adjusting bass, treble, HPF, levels, and volume for multi-zone audio.
Configuring amp assignments, volume, GUI appearance, and format.
Selecting input sources and related playback settings for various devices.
Mapping sources to HDMI, Digital, Component, and iPod dock connectors.
Playback, auto preset, preset skip, preset name, and input mode for TUNER.
Playback, auto tune, preset skip, and input mode for NET/USB and DAB.
Playback mode, repeat, shuffle, and viewing settings for iPod.
Descriptions of standard playback and 10 DENON DSP surround modes.
Modes for playing Dolby Digital, DTS, and 2-channel sources with surround effects.
Adjusting surround sound parameters based on playback source and mode.
Adjustments for movie sound quality, dynamic range, low-frequency effects, and center image.
Settings for soundstage, delay, effects, and acoustic environment simulation.
Automatic surround mode selection and surround back channel output configuration.
Selecting room equalization modes and adjusting bass/treble tone controls.
Restoring compressed audio quality and adjusting bass/treble for richer sound.
Instructions for turning the unit on, off, and to standby mode.
A detailed table showing parameter adjustability across different surround modes and input signals.
Common issues with power, sound, display, and indicators, with countermeasures.
Troubleshooting remote control operation issues like non-response or incorrect range.
