Denon AVR-4311CI User Manual

97
Basic versionSimple version InformationAdvanced version
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
MANUAL SETUP
Setting items Setting details
Distance
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Feet / Meters : Set the unit of distance.
Step : Set the minimum variable width of the distance.
• 1ft / 0.1ft
• 0.1m / 0.01m
Default : The “Distance” settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Return all settings
to the default?” prompt is displayed. Select either “Yes” or “No”, and
press ENTER.
Front L / Front R / Center / Subwoofer / Subwoofer 1
z1
/ Subwoofer
2
z2
/ Surr.L / Surr.R / Surr.Back L
z2
/ Surr.Back R
z2
/ Front Height
L / Front Height R / Front Wide L / Front Wide R : Select the speaker.
z1 When the “Speaker Config.” – “Subwoofer” setting (vpage96) is
set to “2 spkrs”, “Subwoofer 1” and “Subwoofer 2” are displayed.
z2 When the “Speaker Config.” – “Surround Back” setting (vpage96)
is set to “1 spkr”, “Surround Back” is displayed.
• 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.
• The speakers that can be selected differ depending on the “Amp Assign”
(vpage95) and “Speaker Config.” (vpage95) settings.
• Default settings :
Front L / Front R / Center / Subwoofer / Subwoofer 1 / Subwoofer 2 /
Front Height L / Front Height R / Front Wide L / Front Wide R : 12.0 ft
(3.6 m)
Surr. L / Surr. R / Surr.Back L / Surr.Back R : 10.0 ft (3.0 m)
• Set the difference in the distance between the speakers to less than 20
ft (6.0 m).
NOTE
Speakers set to “None” in “Speaker Config.” (vpage 95) are not
displayed.
Setting items Setting details
Channel Level
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone : Output test tone.
• Front L / Front Height L / Center / Front Height R / Front R / Front
Wide R / Surround R / Surr.Back R
z1
/ Surr.Back L
z1
/ Surround
L / Front Wide L / Subwoofer / Subwoofer 1
z2
/ Subwoofer 2
z2
/
Subwoofer 1+2
z2
: Select the speaker.
z1 When the “Speaker Config.” – “Surround Back” setting (vpage96)
is set to “1 spkr”, “Surr.Back” is displayed.
z2 When the “Speaker Config.” – “Subwoofer” setting (vpage96) is
set to “2 spkrs”, “Subwoofer 1”, “Subwoofer 2” and “Subwoofer
1+2” are displayed.
• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.
• After aligning both the distances and levels of subwoofer 1 and
subwoofer 2, please adjust subwoofer 1+2. These parameters affects
the volume of subwoofer 1+2.
• By clicking o p, the volume of both subwoofer 1 and subwoofer 2
moves down or up together.
• If one of subwoofer1 or subwoofer 2 reaches ±12.0 dB, then the cursors
don’t move further.
• When “Channel Level” is adjusted, the adjusted values are set for all the
surround modes. To adjust the channel level separately for the different
surround modes, use the operation see page 66.
NOTE
• Speakers set to “None” in the “Speaker Config.” (vpage95) settings
are not displayed.
• When a headphones jack is inserted in the PHONES jack of this unit, the
“Channel Level” is not displayed.
Default : The “Channel Level” settings are returned to the default settings.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
1.AVR4311CIEU_ENG_108.indd 97 2010/08/30 20:11:07

Denon AVR-4311CI Specifications

General

Brand	Denon
Model	AVR-4311CI
Category	Stereo Receiver
Language	English