Denon AVR-4311CI - Zone Setup

103
Basic versionSimple version InformationAdvanced version
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
MANUAL SETUP
Setting items Setting details
Rhapsody Account
Set or change Username
and Password (vpage46
“Listening to Rhapsody”).
Username / Password / Clear
• For character input, see page 78.
Napster Account
Set or change Username
and Password (vpage42
“Listening to Napster”).
Username / Password / Clear
• For character input, see page 78.
Network Info.
Display network information.
Friendly Name / DHCP / IP Address / MAC Address
Zone Setup
Default settings are underlined.
Set the audio to play back with multi-zone (ZONE2, ZONE3).
Setting items Setting details
Bass
Adjust low frequency range
(bass).
–10dB – +10dB (0dB)
Treble
Adjust high frequency range
(treble).
–10dB – +10dB (0dB)
HPF
Make settings for cutting
the low range to reduce
distortion in the bass.
ON : The low range is attenuated.
OFF : The low range is not attenuated.
Lch Level
Adjust the left channel
output level.
–12dB – +12dB (0dB)
The “Lch Level” can be set when “Channel“ (vpage103) is set to
“Stereo“.
Rch Level
Adjust the right channel
output level.
–12dB – +12dB (0dB)
The “Rch Level” can be set when “Channel“ (vpage103) is set to
“Stereo“.
Channel
Set the signal output from
multi-zone.
Stereo : Select stereo output.
Mono : Select mono output.
When “Amp Assign” – “Assign Mode” (vpage95) is set to “Z2/3-
MONO”, the “Channel” setting is automatically set to “Mono”.
Setting items Setting details
Volume Level
Set the volume output level.
Variable : Volume adjustment is enabled by main unit and remote control
unit.
–40dB (41) : Fix volume at –40 dB. Set when adjusting volume by external
amplifi er.
0dB (81) : Fix volume at 0 dB. Set when adjusting volume by external
amplifi er.
When “Amp Assign” – “Assign Mode” (vpage 95) is set to
“ZONE2”, “ZONE2/3” or “Z2/3-MONO”, the “Volume Level” setting
is automatically set to “Variable”.
Volume Limit
Make a setting for
maximum volume.
OFF : Do not set a maximum volume.
–20dB (61) / –10dB (71) / 0dB (81)
• This can be set when the multi-zone “Volume Level” setting (vpage103)
is “Variable”.
• This is displayed from 0 to 99 when “Volume Display” (vpage104) is set
to “Absolute”.
Power On Level
Defi ne the volume setting
that is active when the
power is turned on.
Last : Use the memorized setting from the last session.
– – –dB (0) : Always mute when power is turned on.
–80dB – 18dB (1 – 99) : The volume is adjusted to the set level.
• This can be set when the multi-zone “Volume Level” setting (vpage103)
is “Variable”.
• This is displayed from 0 to 99 when “Volume Display” (vpage104) is set
to “Absolute”.
Mute Level
Set the amount of
attenuation when muting
is on.
Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
1.AVR4311CIEU_ENG_108.indd 103 2010/08/30 20:11:09