Denon AVR-4311CI - Operating The Connected Devices By Remote Control Unit; Operating the Main Remote Control Unit; Registering Preset Codes

108
Operating the connected devices by remote control unit
Operating the main remote control unit
Registering the supplied preset codes in the remote control unit
enables you to operate devices made by other manufacturers.
Operating AV equipment
1
Press ZONE SELECT to select a
zone for operation.
The zone mode indicator corresponding
to the operating zone lights.
• The mode switches each time ZONE
SELECT
is pressed.
M
Select for the operations in MAIN
ZONE.
Z2
Select for the operations in ZONE2.
Z3
Select for the operations in ZONE3.
Z4
Not used.
2
Press the input source select button (vpage 28).
• The input source for the zone selected in step 1 is switched.
• The operation mode of the remote control unit is switched as
shown in the table.
Input
source
select
button
Input
source of
this unit
Operation mode
Display
Devices controllable with the
remote control unit
– This unit (AMP-operation)
z
2
z
1
BD
Device registered on the BD
button
z
1
DVD
Device registered on the DVD
button
z
1
TV
Device registered on the TV
button
z
1
SAT/CBL
Device registered on the SAT/
CBL
button
z
1
DVR
Device registered on the DVR
button
z
1
GAME
Device registered on the GAME
button
z
1
V.AUX
Device registered on the V.AUX
button
z
1
CD
Device registered on the CD
button
NET/USB or
DOCK
iPod connected to the USB port
or control dock for iPod.
DOCK Control dock for iPod
NET/USB
• Network function
• iPod or USB memory device
connected to the USB port
SIRIUS SIRIUS Satellite Radio
PHONO This unit (AMP-operation)
z
2
HD Radio HD Radio receiver
z1 If a preset code is registered for this button, the remote control
unit of this unit can control another devices.
z2 This operation mode enables you to operate iPod, USB, Control
dock for iPod, Network function, SIRIUS, and HD Radio receiver.
When SOURCE SELECT is pressed, the AMP-operation mode starts
automatically.
NOTE
If the mode of the remote control unit is set to other than AMP-
operation mode, press AMP to switch the remote control unit to the
AMP-operation mode to perform the following operations:
• For menu operation by pressing MENU
• For setting the channel level of the unit by pressing CH LEVEL
• For turning power in each zone on or off by pressing ZONE/DEVICE
ON
or ZONE/DEVICE OFF.
3
Operate this unit or the device whose input source is
switched.
• For details, refer to the operating instructions for each device.
For operations of iPod, SIRIUS, HD Radio receiver and USB
memory device, see the following pages.
• iPod (vpage31, 32)
• SIRIUS (vpage35)
• HD Radio receiver (vpage37)
• Network function (vpage40 – 47)
• USB memory device (vpage48)
Registering preset codes
When preset codes are registered in the included remote control unit,
it can then be used to operate any devices you have, such as DVD
players or TVs made by different manufacturers.
In this menu, you can search and display the preset codes that can be
preset in the included remote control unit.
n Buttons used for operating the devices
q ZONE/DEVICE ON, ZONE/DEVICE OFF
For switching power of each device on or off.
w uio p, ENTER, RETURN
For menu operation of each device.
e MENU, SETUP, TOP MENU
For displaying the menu of each device.
r 1, 2, 3, 6, 7, 8, 9
t Number button (0 – 9, +10)
y CH +, CH –
u TV POWER, TV INPUT
For operating a TV
This button is enabled in any mode.
For details on operation with the remote control unit, see pages 31,
32, 35, 37, 40 – 43, 45, 47, 49, 111.
1.AVR4311CIEU_ENG_108.indd 108 2010/08/30 20:11:11