Denon AVR-4311CI - DENON Original Surround Playback; Stereo Playback; Direct Playback; Pure Direct Playback

52
DENON original surround playback
1
Playing the source (vpage 29 –
49).
2
Press SIMULATION to select the
surround mode.
• If DSP SIMULATION on the main unit is
pressed, the same function as with the
remote control unit can be obtained.
• Each time SIMULATION is pressed, the
surround mode is switched.
MULTI CH
STEREO
This mode is for enjoying stereo sound from all
speakers.
WIDE SCREEN
This mode is for enjoying the atmosphere of
viewing a movie on a large screen.
SUPER
STADIUM
This mode is suited for viewing sports programs.
ROCK ARENA
This mode is for enjoying the atmosphere of a live
concert in an arena.
JAZZ CLUB
This mode is for enjoying the atmosphere of a live
concert in a jazz club.
CLASSIC
CONCERT
This mode is for appreciating classical concert
programs.
MONO MOVIE
z
This mode is for playing monaural movie sources
with surround sound.
VIDEO GAME
This mode is suited for achieving surround sound
with video games.
MATRIX
This mode lets you add a spacious feel to stereo
music sources.
VIRTUAL
This mode is for enjoying surround effects using
only the front speakers or headphones.
z When playing sources recorded in monaural in the “MONO
MOVIE” mode, the sound will be off balance with a single
channel (left or right), so input to both channels.
Depending on the program source being played, it may not be possible
to achieve a satisfactory surround effect. In this case, try other modes
to achieve a sound field suited to your tastes.
Stereo playback
This is the mode for playing in stereo. The tone can be adjusted.
• Sound is output from the front left and right speakers and subwoofer.
• If multichannel signals are input, they are mixed down to 2-channel
audio and are played.
1
Playing the source (vpage 29 –
49).
2
Press D/ST to select “STEREO”.
Stereo playback begins.
• If
DIRECT/STEREO on the main unit is
pressed, the same function as with the
remote control unit can be obtained.
Direct playback
Sound recorded in source is played as is.
• Surround back signals or front height signals are not created.
• In this mode, the following items cannot be adjusted.
• Tone (vpage88) • MultEQ
®
XT 32 (vpage89)
• Dynamic EQ
®
(vpage89) • Dynamic Volume
®
(vpage90)
• Dolby Volume (vpage91) • RESTORER (vpage92)
1
Playing the source (vpage 29 –
49).
2
Press D/ST to select “DIRECT”.
Direct playback begins.
• If
DIRECT/STEREO on the main unit is
pressed, the same function as with the
remote control unit can be obtained.
Pure direct playback
This mode is for playback in higher sound quality than in “Direct
playback” mode.
• The following circuits that affect sound quality are set to off.
• Main unit’s display circuit (The display is turned off.)
• Analog video input/output circuit
• Surround back signals or front height signals are not created.
• In this mode, the following items cannot be adjusted.
• Tone (vpage88) • MultEQ
®
XT 32 (vpage89)
• Dynamic EQ
®
(vpage89) • Dynamic Volume
®
(vpage90)
• Dolby Volume (vpage91) • RESTORER (vpage92)
1
Playing the source (vpage 29 –
49).
2
Press PURE.
The display goes dark, and pure direct
playback begins.
• If
PURE DIRECT on the main unit is
pressed, the same function as with the
remote control unit can be obtained.
• To cancel, press PURE again.
• Video signals are only output when HDMI signals are played in the
PURE DIRECT mode.
NOTE
When in the PURE DIRECT mode, the menu screen is not displayed.
1.AVR4311CIEU_ENG_108.indd 52 2010/08/30 20:10:44