The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
50
59
Insert as fi xed cost in holiday-" me - When passing from HIRED to STOPPED in holiday-time should the parameter of Q.54 be inserted as a
fi xed cost?
No / Yes
60
Insert as percentage in holiday-" me - When passing from HIRED to STOPPED in holiday-time should the parameter of Q.54 be inserted
as a percentage?
No / Yes
61
Insert as fi xed cost in holiday-" me with F2 - Passing from HIRED to STOPPED in holiday-time should the parameter of Q.54 be inserted
as a fi xed cost pressing F2?
No / Yes
62
Insert as percentage in holiday-" me with F2 - Passing from Hired to Stopped in holiday-time should the parameter of Q.54 be inserted
as a percentage pressing F2?
No / Yes
PR OG-DATE N. 3
63
Block-number in Prog-Date 3 - The block number (absolute) to be used during the date and hour programmed in Prog-Date 3. The
allowed value goes from 0 (min) to 62 (max).
0 - 62
64
Block-off set in Prog-Date 3 - The block offset (relative) to be used during the date and hour programmed in Prog-Date 3. The relative
block offset is the number of blocks to add to the current block number in order to obtain the new block number. The allowed value
goes from 0 (min) to 62 (max).
0 - 62
65
Percentage or cost in Prog-Date 3 - This is the percentage or the cost that will be applied during the date and time as programmed in
Prog-Date 3. The interpretation as a percentage or as a cost depends on questions Q.66 to Q.73. In case of percentage consider Q.66
to Q.69, Q.71 and Q.73. Questions Q.70 and Q.72 should be answered with: NO. In case of cost consider Q.70 and Q.72. Questions
Q.66 to Q.69, Q.71 and Q.73 should be answered with: NO. The cost is given in the local currency with an accuracy of 1. The allowed
value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fi xed decimal point. The percentage is given with an
accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/
cost
66
Increase unit-cost in Prog-Date 3 - Should the unit-cost (Q.8 to Q.10) in Prog-Date 3 be increased based on the percentage (Q.65) ?
No / Yes
67
Increase ini" al-cost in Prog-Date 3 - Should the initial-cost (Q.11) in Prog-Date 3 be increased based on the percentage (Q.65)?
No / Yes
68
Decrease unit-distance in Prog-Date 3 - Should the unit-distance (Q.2 to Q.4) in Prog-Date 3 be decreased based on the percentage
(Q.65)?
No / Yes
69
Decrease unit-wai" ng-" me in Prog-Date 3 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 3 be decreased based on the
percentage (Q.65)?
No / Yes
70
Insert as fi xed cost in Prog-Date 3 - When passing from HIRED to STOPPED in Prog-Date 3 should the parameter of Q.65 be inserted
as a fi xed cost?
No / Yes
71
Insert as percentage in Prog-Date 3 - When passing from HIRED to STOPPED in Prog-Date 3 should the parameter of Q.65 be inserted
as a percentage?
No / Yes
72
Insert as fi xed cost in Prog-Date 3 with F2 - Passing from HIRED to STOPPED in Prog-Date 3 should the parameter of Q.65 be inserted
as a fi xed cost pressing F2?
No / Yes
73
Insert as percentage in Prog-Date 3 with F2 - Passing from HIRED to STOPPED in Prog-Date 3 should the parameter of Q.65 be
inserted as a percentage pressing F2?
No / Yes
PRO G-DATE N. 4
74
Block-number in Prog-Date 4 - The block number (absolute) to be used during the date and hour programmed in Prog-Date 4. The
allowed value goes from 0 (min) to 62 (max).
0 - 62
75
Block-off set in Prog-Date 4 - The block offset (relative) to be used during the date and hour programmed in Prog-Date 4. The relative
block offset is the number of blocks to add to the current block number in order to obtain the new block number. The allowed value
goes from 0 (min) to 62 (max).
0 - 62
76
Percentage or cost in Prog-Date 4 - This is the percentage or the cost that will be applied during the date and time as programmed in
Prog-Date 4. The interpretation as a percentage or as a cost depends on questions Q.77 to Q.84. In case of percentage consider
Q.77 to Q.80, Q.82 and Q.84. Questions Q.81 and Q.83 should be answered with: NO. In case of cost consider Q.81 and Q.83.
Questions Q.77 to Q.80, Q.82 and Q.84 should be answered with: NO. The cost is given in the local currency with an accuracy of 1.
The allowed value goes from 0 (min) to 65535 (max). See Q.273 and Q.274 for adding a fi xed decimal point. The percentage is given
with an accuracy of 0.1. The allowed value goes from 0 (min) to 6553.5 (max).
0 – 65535
percentage/
cos
t
77
Increase unit-cost in Prog-Date 4 - Should the unit-cost (Q.8 to Q.10) in Prog-Date 4 be increased based on the percentage (Q.76)?
No / Yes
78
Increase ini" al-cost in Prog-Date 4 - Should the initial-cost (Q.11) in Prog-Date 4 be increased based on the percentage (Q.76)?
No / Yes
79
Decrease unit-distance in Prog-Date 4 - Should the unit-distance (Q.2 to Q.4) in Prog-Date 4 be decreased based on the percentage
(Q.76)?
No / Yes
80
Decrease unit-wai" ng-" me in Prog-Date 4 - Should the unit-waiting-time (Q.5 to Q.7) in Prog-Date 4 be decreased based on the
percentage (Q.76)?
No / Yes
81
Insert as fi xed cost in Prog-Date 4 - When passing from HIRED to STOPPED in Prog-Date 4 should the parameter of Q.76 be inserted
as a fi xed cost?
No / Yes
82
Insert as percentage in Prog-Date 4 - When passing from HIRED to STOPPED in Prog-Date 4 should the parameter of Q.76 be
inserted as a percentage?
No / Yes
83
Insert as fi xed cost in Prog-Date 4 with F2 - Passing from HIRED to STOPPED in Prog-Date 4 should the parameter of Q.76 be
inserted as a fi xed cost pressing F2?
No / Yes
84
Insert as percentage in Prog-Date 4 with F2 - Passing from HIRED to STOPPED in Prog-Date 4 should the parameter of Q.76 be
inserted as a percentage pressing F2?
No / Yes
PROG -DATE N. 5
85
Block-number in Prog-Date 5 - The block number (absolute) to be used during the date and hour programmed in Prog-Date 5. The
allowed value goes from 0 (min) to 62 (max).
0 - 62
To Next Page
Loading...