The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
49
31
Is extra charge n.4 a percentage or a cost? - Determines whether extra charge number 4 (the value of Q.27) is to be interpreted as a
percentage (Yes) or as a cost (No). The allowed answer is either 0 (No: Fixed-cost) or 1 (Yes: percentage of the fare).
0=cost
1=
percentage
32
Remember last used block num.? (next fare) - Should the last block number that has been used be remembered in order to be used
again for the next fare?
No / Yes
33
Enable discard current fare in Stopped? - This option enables the possibility to discard the statistics of the current fare by pressing the
keys F5 and F1, passing to ForHire. The allowed answer is either: No(enabled) or Yes (disabled).
No / Yes
34
Enable/disable measurements? - Should the distance measurement be disabled while in Stopped? The allowed answer is either:
No(enabled) or Yes (disabled).
No / Yes
35
Enable/disable measurements? - Should the waiting-time measurement be enabled while in Stopped? The allowed answer is either:
No(enabled) or Yes (disabled).
No / Yes
36
Enable/disable measurements? - Should the distance measurement be disabled while in Hired? The allowed answer is either:
No(enabled) or Yes (disabled).
No / Yes
37
Enable/disable measurements? - Should the waiting-time measurement be disabled while in Hired? The allowed answer is either:
No(enabled) or Yes (disabled).
No / Yes
NIGHT TIME (Prog - Date N. 1)
38
Start of night-! me - This is the moment (whole or half hour) in which night-time starts. The time is given in whole hours with an accuracy
of 1 hour. The allowed value goes from 0 (min) to 23 (max). It is also possible to specify half hours. In order to do this add 100 to the
programmed value. For example, to program the hour 22:30 use the value 122.
0 - 23
39
End of night-! me - This is the moment (whole or half hour) in which night-time ends. The time is given in whole hours with an accuracy
of 1 hour. The allowed value goes from 0 (min) to 23 (max). It is also possible to specify half hours. In order to do this add 100 to the
programmed value. For example, to program the hour 06:30 use the value 106.
0 - 23
40
Block-number in night-! me - The block number (absolute) to be used during the hours considered night-time (Prog-Date 1) as
programmed in Q.38 and Q.39. The allowed value goes from 0 (min) to 62 (max).
0 - 62
41
Block-off set in night-! me - The block offset (relative) to be used during the hours considered night-time (Prog-Date 1) as programmed
in Q.38 and Q.39. The relative block offset is the number of blocks to add to the current block number in order to obtain the new block
number. The allowed value goes from 0 (min) to 62 (max).
0 - 62
42
Percentage or cost in night-! me - This is the percentage or the cost that will be applied during night-time. The interpretation as a
percentage or as a cost depends on questions Q.43 to Q.50. In case of percentage consider Q.43 to Q.46, Q.48 and Q.50. Questions
Q.47 and Q.49 should be answered with: NO. In case of cost consider Q.47 and Q.49. Questions Q.43 to Q.46, Q.48 and Q.50
should be answered with: NO. The cost is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to
65535 (max). See Q.273 and Q.274 for adding a fi xed decimal point. The percentage is given with an accuracy of 0.1. The allowed
value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/
cost
43
Increase unit-cost in night-! me - Should the unit-cost (Q.8 to Q.10) in night-time be increased based on the percentage (Q.42)?
No / Yes
44
Increase ini! al-cost in night-! me - Should the initial-cost (Q.11) in night-time be increased based on the percentage (Q.42)?
No / Yes
45
Decrease unit-distance in night-! me - Should the unit-distance (Q.2 to Q.4) in night-time be decreased based on the percentage
(Q.42)?
No / Yes
46
Decrease unit-wai! ng-! me in night-! me - Should the unit-waiting-time (Q.5 to Q.7) in night-time be decreased based on the percentage
(Q.42)?
No / Yes
47
Insert as fi xed cost in night-! me - Insert Q.42 at Stopped in N-T as Fixed Cost? When passing from Hired to Stopped in night-time
should the parameter of Q.42 be inserted as a fi xed cost ?
No / Yes
48
Insert as percentage in night-! me - When passing from HIRED to STOPPED in night-time should the parameter of Q.42 be inserted as
a percentage?
No / Yes
49
Insert as fi xed cost in night-! me with F2 - Passing from HIRED to STOPPED in night-time should the parameter of Q.42 be inserted as
a fi xed cost pressing key F2?
No / Yes
50
Insert as percentage in night-! me with F2 - Passing from Hired to Stopped in night-time should the parameter of Q.42 be inserted as a
percentage pressing key F2?
No / Yes
H OLIDAY ( Prog-Date N. 2 )
51
Day of week considered holiday - This is the number that corresponds with the day of the week that is to be considered a holiday. The
allowed number goes from 0 (min) to 7 (max). The numbers have the following meaning:
0 - 7
0 ==> Disabled 1 ==> Monday 2 ==> Tuesday 3 ==> Wednesday
4 ==> Thursday 5 ==> Friday 6 ==> Saturday 7 ==> Sunday
52
Block-number in holiday-! me - The block number (absolute) to be used during the days considered holiday-time (Prog-Date 2) as
programmed in Q.51. The allowed value goes from 0 (min) to 62 (max).
0 - 62
53
Block-off set in holiday-! me - The block offset (relative) to be used during the week-days considered holiday-time (Prog-Date 2) as
programmed in Q.51. The relative block offset is the number of blocks to add to the current block number in order to obtain the new
block number. The allowed value goes from 0 (min) to 62 (max).
0 - 62
54
Percentage or cost in holiday-! me - This is the percentage or the cost that will be applied during holiday-time. The interpretation as a
percentage or as a cost depends on questions Q.55 to Q.62. In case of percentage consider Q.55 to Q.58, Q.60 and Q.62. Questions
Q.59 and Q.61 should be answered with: NO. In case of cost consider Q.59 and Q.61. Questions Q.55 to Q.58, Q.60 and Q.62
should be answered with: NO. The cost is given in the local currency with an accuracy of 1. The allowed value goes from 0 (min) to
65535 (max). See Q.273 and Q.274 for adding a fi xed decimal point. The percentage is given with an accuracy of 0.1. The allowed
value goes from 0 (min) to 6553.5 (max).
0 - 65535
percentage/
cost
55
Increase unit-cost in holiday-! me - Should the unit-cost (Q.8 to Q.10) in holiday-time be increased based on the percentage (Q.54)?
No / Yes
56
Increase ini! al-cost in holiday-! me - Should the unit-cost (Q.11) in holiday-time be increased based on the percentage (Q.54)?
No / Yes
57
Decrease unit-distance in holiday-! me - Should the unit-distance (Q.2 to Q.4) in holiday-time be decreased based on the percentage
(Q.54)?
No / Yes
58
Decrease unit-wai! ng-! me in holiday-! me - Should the unit-waiting-time (Q.5 to Q.7) in holiday-time be decreased based on the
percentage (Q.54)?
No / Yes
To Next Page
Loading...