The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
59
269
Inhibit clock-! me programming from panel? - Should the possibility to program the clock-! me from the panel be inhibited?
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
270
Disable visualiza! on of chronometer? - Should the visualization of the chronometer on the display be disabled?
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
271
In ForHire show text “F-HIRE” on display? - Should the text “F-HIRE” be shown on the primary display when in ForHire?
The allowed answer is either: 0 (No: show text) or: 1 (Yes: don’t show text).
No / Yes
272
Distance is in yards ? (if not: metres) - The distance in Q.2 to Q.4 is in yards? If not then the distance is in metres.
The allowed answer is either: 0 (No: metres) or: 1 (Yes: yards).
0=metres
1=yard
273
Put ON the decimal point at pos. 2/3? Should the decimal point between the second and third position (from the right) be put ON? For
example: 5.00.
The allowed answer is either: 0 (No: put OFF) or: 1 (Yes: put ON).
No / Yes
274
Put ON the decimal point at pos. 3/4? - Should the decimal point between the third and fourth position (from the right) be put ON? For
example: 5.000.
The allowed answer is either: 0 (No: put OFF) or: 1 (Yes: put ON).
No / Yes
275
From Stopped back to Hired with key F3? - Should it be possible to go from Hired to Stopped pressing key F3?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
276
Chronometer shown as 9959? (if not: 9-59) - Should the time of the chronometer be shown as 9959 on the secondary display? If not, it
will be shown as 9-59. So, practically the dash is sacrifi ced for gaining another digit of the chronometer.
The allowed answer is either: 0 (No: 9-59) or: 1 (Yes: 9959).
No / Yes
277
Chronometer shows minutes ? (if not: seconds) - Should the chronometer show minutes on the secondary display? If not, it will show
seconds. The allowed answer is either: 0 (No: seconds) or: 1 (Yes: minutes).
No / Yes
278
Show clock/year for 5 seconds with F4/F5? - If this question is enabled and key F4 is pressed then the clock will be shown on the
secondary display and the date on the main display for 5 seconds. With this question enabled and key F5 is pressed then the year will
be shown on the main display for 5 seconds. This question is only meaningfull if the visualization of the clock has been disabled with
Q.268. The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
279
Disable manual programming of the Euro currency?
No / Yes
280
Disable the Euro conversion in Hired?
No / Yes
281
Disable the Euro conversion in Stopped?
No / Yes
282
Put off displays in ForHire a# er ! me of Q.283? – If yes then in ForHire the displays will be put off after the time established in Q.283.
See also Q.283. The allowed answer is either: 0 (No) or: 1 (Yes).
No / Yes
283
Stand-by ! me in Hired and Stopped: in Hired and Stopped this is the time after which the taximeter will go in stand-by. In stand-by the
internal functions are all active but the display is put OFF. The taximeter is ‘woken-up’ by either pressing any key or by the fi rst pulse
from the transducer. The time is given in minutes with an accuracy of 1 minute. The allowed value goes from 0 (min) to 255 (max).
0 - 255
minutes
284
Shut-down ! me in ForHire: in ForHire this is the time after which the taximeter will be shut-down. In shut-down all internal functions
except the clock are disactivated and also the display is put OFF. The taximeter is ‘woken-up’ by either pressing the F1 key or by the
fi rst pulse from the transducer. Also see Q.192. If the answer is 0 the taximeter doesn’t switch-off automatically anymore. Is this case it
can only be switched-off manually by pressing in For-Hire position F3 and F5 together. The time is given in minutes with an accuracy of
1 minute. The allowed value goes from 0 (min) to 255 (max).
0 - 255
minutes
285
Time of displaying total cost: this is the time during which the total cost will be shown on the primary display in Stopped. Initialy, in
Hired the primary display shows the accumulated fare cost and the secondary display shows the extra-charge. Upon entering Stopped
the secondary display goes OFF and the primary display shows the total cost (the sum) for the time programmed here. After this time
both displays show their original data again. The time is given in seconds with an accuracy of 1 second. The allowed value goes from 0
(min) to 255 (max). The value of 0 disables this function. Between 1 and 254 the Time sum is in seconds. In case of a value of 255 this
function becomes manual at the fi rst attempt Sum at the second releases the Sum.
0 - 255
286
Restart ! me in Hired or Stopped without power: if the power is removed from the taximeter while in Hired or in Stopped then this is the
time after which the fare-cost will be discarded and the taximeter will restart in Stopped. The time is given in seconds with an accuracy
of 1 second. The allowed value goes from 0 (min) to 255 (max).
0 - 255
seconds
287
Is Euro the main currency? - Choosing Yes, the taximeter will work only in Euro (also the ticket printout will show values only in Euro)
No / Yes
To Next Page
Loading...