The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
58
244
State of taximeter for light n. 2 ON: this is the state (or states) of the taximeter in which the light number 2 should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 2 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire =
128
Stopped
= 64
Hired =
32
None= 0
LIGHT N . 3
245
Enable light n. 3 ON in day-! me? - Should it be possible for light number 3 to be ON during the day-time?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
246
Light n. 3 must " ash? - If Yes light number 3 will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash).
No / Yes
247
Light n. 3 must go ON in overspeed? - If Yes then light number 3 will go ON in case the actual velocity is higher than the velocity
programmed in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
248
Light n. 3 must go on below overspeed?
No / Yes
from Q 249 / available for any possible software extension / to Q 251
252
Light n. 3 ON in this tari# -block? - With Yes light number 3 will go ON in the corrisponding tariff-block. The allowed answer is either: 0
(No: OFF) or: 1 (Yes: ON).
No / Yes
253
Block-number for light n. 3 ON: this is the number of the tariff-block where light number 3 should be ON. The allowed value goes from 0
(min) to 62 (max).
0 - 62
254
Prog-Date-number for light n. 3 ON: this is the number of the Prog-Date where light number 3 should be ON. The allowed value goes
from 0 (min) to 8 (max).
0 - 8
255
State of taximeter for light n. 3 ON: this is the state (or states) of the taximeter in which the light number 3 should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 3 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire =
128
Stopped
= 64
Hired =
32
None=
0
LIGHT N. 4
256
Enable light n. 4 ON in day-! me? - Should it be possible for light number 4 to be ON during the day-time?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
257
Light n. 4 must " ash? - If Yes light number 4 will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash).
No / Yes
258
Light n. 4 must go ON in overspeed? - If Yes then light number 4 will go ON in case the actual velocity is higher than the velocity
programmed in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
259
Light n. 4 must go on below overspeed?
No / Yes
from Q 260 to Q 262 available for any possible software extension
263
Light n. 4 ON in this tari# -block? - With Yes light number 4 will go ON in the corrisponding tariff-block. The allowed answer is either: 0
(No: OFF) or: 1 (Yes: ON).
No / Yes
264
Block-number for light n. 4 ON: this is the number of the tariff-block where light number 4 should be ON. The allowed value goes from 0
(min) to 62 (max).
0 - 62
265
Prog-Date-number for light n. 4 ON: this is the number of the Prog-Date where light number 4 should be ON. The allowed value goes
from 0 (min) to 8 (max).
0 - 8
266
State of taximeter for light n. 4 ON: this is the state (or states) of the taximeter in which the light number 4 should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 4 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
ForHire=
128
Stopped=
64
Hired=
32
None=
0
VARIOUS FUNCTION
267
Must be Euro the default currency? - Establish default currency starting the trip No=Local currency Yes=Euro
No / Yes
268
Disable visualiza! on of clock on display? - Should the visualiza! on of the clock on the (secondary) display be disabled?
The allowed answer is either: 0 (No: enabled) or: 1 (Yes: disabled).
No / Yes
To Next Page
Loading...