The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
57
214
The taxi-light must go ON in overspeed? - If Yes then the taxi-light will go ON in case the actual velocity is higher than the velocity
programmed in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
215 Taxi-light must go on overspeed? No / Yes
from Q 216 / available for any possible software extension / to Q 218
219
Taxi-light ON in this tari! -block? - With Yes the taxi-light will go ON in the corrisponding tariff-block.
The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
220
Block-number for taxi-light to be ON: this is the number of the tariff-block where the taxi-light should be ON. The allowed value goes
from 0 (min) to 62 (max).
0 - 62
221
Prog-Date-number for taxi-light to be ON: this is the number of the Prog-Date where the taxi-light should be ON. The allowed value goes
from 0 (min) to 8 (max).
0 - 8
222
State of taximeter for taxi-light to be ON - This is the state (or states) of the taximeter in which the taxi-light should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON the taxi-light in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire =
128
Stopped
= 64
Hired =
32
None
= 0
LIGHT N. 1
223
Enable light n. 1 ON in day-" me? - Should it be possible for light number 1 to be ON during the day-time?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
224
Light n. 1 must # ash? - If Yes light number 1 will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash).
No / Yes
225
Light n. 1 must go ON in overspeed? - If Yes then light number 1 will go ON in case the actual velocity is higher than the velocity
programmed in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
226
Light n. 1 must go on below overspeed?
No / Yes
from Q 227/ available for any possible software extension / to Q 229
230
Light n. 1 ON in this tari! -block? - With Yes light number 1 will go ON in the corrisponding tariff-block.
The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
231
Block-number for light n. 1 ON: this is the number of the tariff-block where light number 1 should be ON.
The allowed value goes from 0 (min) to 62 (max).
0 - 64
232
Prog-Date-number for light n. 1 ON: this is the number of the Prog-Date where light number 1 should be ON.
The allowed value goes from 0 (min) to 8 (max).
0 - 8
233
State of taximeter for light n. 1 ON: this is the state (or states) of the taximeter in which the light number 1 should be ON.
The allowed values are: 0 (none) - 32 (Hired) - 64 (Stopped) - 128 (ForHire).
Also combinations are allowed. In that case the values need to be summed together.
For example, to put ON light number 1 in Stopped and also in ForHire the value to program is: 64 + 128 = 192.
For Hire =
128
Stopped =
64
Hired =
32
None = 0
LIGHT N. 2
234
Enable light n. 2 ON in day-" me? Should it be possible for light number 2 to be ON during the day-time?
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
No / Yes
235
Light n. 2 must # ash? - If Yes light number 2 will fl ash. The allowed answer is either: 0 (No: no fl ash) or: 1 (Yes: fl ash).
No / Yes
236
Light n. 2 must go ON in overspeed? - If Yes then light number 2 will go ON in case the actual velocity is higher than the velocity
programmed in Q.200. The allowed answer is either: 0 (No: OFF) or: 1 (Yes: ON).
No / Yes
237
Light n. 2 must go on below overpseed?
No / Yes
from Q 238 / available for any possible software extension / to Q 240
241
Light n. 2 ON in this tari! -block? - With Yes light number 2 will go ON in the corrisponding tariff-block. The allowed answer is either: 0
(No: OFF) or: 1 (Yes: ON).
No / Yes
242
Block-number for light n. 2 ON: this is the number of the tariff-block where light number 2 should be ON. The allowed value goes from 0
(min) to 62 (max).
0 - 62
243
Prog-Date-number for light n. 2 ON: this is the number of the Prog-Date where light number 2 should be ON. The allowed value goes
from 0 (min) to 8 (max).
0 - 8
To Next Page
Loading...