The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely confi dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
63
341
Enable programming forfait with front keys? - If yes then, with the taximeter in Hired and pressing the keys F2 + F5 together, the forfait
amount can be programmed on the primary display. On the secondary display the text FORFA will be shown.
Programming:
pressing key F2 increases the amount with 1 unit pressing key F3 increases the amount with 10 units;
pressing key F4 increases the amount with 100 units pressing key F5 increases the amount with 1000 units;
pressing keys F4 + F5 cancels the modifi cations made up to this point pressing key F1 the forfait programming is exited.
Once exited from the forfait programming the amount shown on the display will not change anymore independently from the run
distance or the waiting time until the next time a new fare is started.
Note:
In order for this function to work well it is necessary to program several
questions in block number 62 because this is the block that is loaded when
the forfait is used according to the following list:
No / Yes
Q13 = 0 : disable key F2
Q21 = 0 : no extra-charge n. 1
Q23 = 0 : no extra-charge n. 2
Q25 = 0 : no extra-charge n. 3
Q27 = 0 : no extra-charge n. 4
Q34 = Yes : disable distance measurement
in Stopped
Q36 = Yes : disable distance measurement in Hired
Q37 = Yes : disable waiting-time measurement in Hired
Q40 = 0 : disable Night-time
Q41 = 0 : disable Night-time
Q52 = 0 : disable Holiday-time
Q53 = 0 : disable Holiday-time
The allowed answer is either: 0 (No: disabled) or: 1 (Yes: enabled).
342
Available for any possible so! ware extension
343
Must the black trips saving opera" on be avoided?
No / Yes
344
Must the cash trips saving opera" on be avoided?
No / Yes
345
Must the Credit trips saving opera" on be avoided?
No / Yes
346
Must the Power off saving opera" on be avoided?
No / Yes
347
Must the shi! s saving opera" on be avoided?
No / Yes
from Q 348 / Available for custom parameters / to Q 367
368
Check Printer Status before start the trip - If Yes the taximeter checks the printer status before startin a new trip and if the printer is not
connected or is not ready then the trip will not start
No / Yes
346
Disable Print out shi! report - If Yes the report will not be printed, if No the report will be printed at the end of the shift
No / Yes
347
Request GPS Coordinates - If Yes the taximeter will request to the dispatcher the coordinates at the start and at the end of the trip
No / Yes
CONNECTION TO THE DISPATCHER
371
Transmit undefi ned status to dispatcher? - Transmit an undefi ned status to the dispatcher?
The allowed answer is either: 0 (No: don’t transmit) or: 1 (Yes: transmit).
No / Yes
372
Transmit ForHire status to dispatcher? - Transmit the ForHire status to the dispatcher?
The allowed answer is either: 0 (No: don’t transmit) or: 1 (Yes: transmit).
No / Yes
373
Transmit Stopped status to dispatcher? - Transmit the Stopped status to the dispatcher?
The allowed answer is either: 0 (No: don’t transmit) or: 1 (Yes: transmit).
No / Yes
374
Transmit Hired status to dispatcher? - Transmit the Hired status to the dispatcher?
The allowed answer is either: 0 (No: don’t transmit) or: 1 (Yes: transmit).
No / Yes
375
Block taximeter if driver ID is 0? - Should the taximeter be blocked if the identifi cation number of the driver is 0?
The allowed answer is either: 0 (No: don’t block) or: 1 (Yes: block).
No / Yes
376
Assign ID 9999999 if driver ID is 0? - Should driver ID 9999999 be assigned if the identifi cation number of the driver is 0?
The allowed answer is either: 0 (No: don’t assign) or: 1 (Yes: assign).
No / Yes
377
If driver = 0, must the meter show “Close” in For Hire mode?
No / Yes
378
Reques" ng Ticket the taximeter powers on the Printer? - If Yes, after printing, the taximeter powers off the printer
No / Yes
379
Defi ne if thermal printer width is 44 mm or 57 mm
No / Yes
To Next Page
Loading...