Why is there no CO waveform on my EDAN Medical Equipment?
If there is no CO waveform on your EDAN Medical Equipment, there may be a bad connection of the CO module. Power off the device and reconnect the CO module. If the problem persists, the CO module may be defective and require replacement.
What to do if EDAN iM80 Monitor displays 'PULSATILE PRESSURE ZERO FAIL'?
If the EDAN Monitor displays 'PULSATILE PRESSURE ZERO FAIL,' ensure the transducer is vented to air and not connected to a patient. Then, try again.
What to do if EDAN iM80 displays 'Art ZERO FAIL'?
If the EDAN Monitor displays 'Art ZERO FAIL', make sure that the transducer is not attached to the patient.
Why does the AG measurement numeric value have an error on EDAN Medical Equipment?
If the AG measurement numeric value has an error on your EDAN Medical Equipment, the GAS module may not have been zeroed for a long time, resulting in inaccurate measurements. Zero the GAS module. Also, ensure the system is in measurement mode and allow a 10-minute warm-up before measuring.
What to do if RESP waveform amplitude is faint on EDAN Medical Equipment?
Adjust waveform amplitude multiple in RESP menu.
Why does paper advance lopsidedly on EDAN Medical Equipment?
If the paper advances lopsidedly in your EDAN Medical Equipment, the assembly or location of the recorder may be incorrect. Calibrate the assembly of the recorder.
Why is there no NIBP numeric value on my EDAN Medical Equipment?
If there's no NIBP (Non-Invasive Blood Pressure) numeric value displayed on your EDAN Medical Equipment, it could be due to a loose cuff or patient movement. Make sure the cuff is properly secured and ask the patient to remain still.
What causes fuses to blow after switching on EDAN Medical Equipment?
If the fuses are blown after switching on your EDAN Medical Equipment, further examination after switching on is required to identify any short circuits in the power or other parts.
What to do with frequent patient activity with EDAN Medical Equipment?
Quiet the patient.
What to do if EDAN Medical Equipment LCD is black, power is on, and the fan runs?
If your EDAN Medical Equipment's LCD has no display but the power indicator is lit and the fan runs, check if the keys sound properly. If they do, the LCD might be defective. However, if the keys don’t sound, the main control board might be the problem, and you should replace it.
Describes the intended medical applications of the monitor.
Provides critical safety warnings and precautions for operation.
Classifies alarms into physiological, technical, and prompts.
Categorizes alarms by severity: high, medium, low.
How to manage alarms, including mute and switching off.
Details physiological alarms, their causes, and levels.
Details technical alarms, their causes, and actions.
Steps for entering patient information for monitoring.
Crucial safety precautions for ECG monitoring.
Safety guidelines specific to respiration monitoring.
Correct placement of electrodes for respiration monitoring.
Important safety precautions for SpO2 monitoring.
How the monitor chooses between ECG/Pulse for alarms.
Critical safety warnings for NIBP measurements.
Detailed steps for performing NIBP measurements.
Safety precautions for temperature monitoring.
Safety guidelines for quick temperature measurements.
Safety precautions for IBP monitoring.
Safety guidelines specific to CO2 monitoring.
Safety precautions for Cardiac Output monitoring.
Safety guidelines for AG monitoring modules.
Performing drug dosage calculations.
Steps for executing drug calculations.
General precautions for cleaning the monitor and accessories.
Detailed instructions for cleaning the monitor enclosure and screen.
Specific cleaning agents and procedures for the monitor.
Items to check during general monitor inspection.
General| Display Type | TFT LCD |
|---|---|
| Respiration | Yes |
| SpO2 | Yes |
| NIBP | Yes |
| Temperature | Yes |
| Pulse Rate | Yes |
| EtCO2 | Optional |
| Battery | Rechargeable lithium-ion battery |
| ECG | 3/5 lead ECG |
| Optional Parameters | Cardiac Output |
| Networking | Wi-Fi, Ethernet |
| Weight | 2.5 kg |
To Next Page
