What should I do if the fuses burn out when a specific part is connected to my EDAN Medical Equipment?
If the fuses burn out when a certain part is connected to your EDAN Medical Equipment, it indicates a short circuit of the specific part. Replace the specific part.
How to fix an EDAN Medical Equipment LCD with no display and the power indicator is off?
If the LCD on your EDAN Medical Equipment has no display and the power indicator is off, the issue could be due to fuse damage (if applicable), power board damage, or component short-circuits. Try replacing the fuse, or the power board. Another solution is to anchor the short-circuited component.
Why does the touch screen on my EDAN Medical Equipment not respond?
If the touch screen on your EDAN Medical Equipment is unresponsive, it could be due to a bad connection of the touch screen wire, touch screen damage, or main control board failure. Check and reconnect the connecting wire. If that doesn't work, consider replacing the touch screen or main control board.
Why does my EDAN Medical Equipment crash unexpectedly?
Unexpected crashes in your EDAN Medical Equipment can be caused by instantaneous intensive network interference, poor power board performance, poor main control board performance, or bad connections of the power board or main control board. Check the power supply and grounding system. You may need to replace the power board or main control board, or replace or repair connectors.
Why are no audio or visual alarms activated on my EDAN Medical Equipment?
If no audio or visual alarms are activated on your EDAN Medical Equipment, it indicates a program failure. Update the software.
Why is there no TEMP value on my EDAN Medical Equipment (T2A, F3000 and TH module)?
If there is no TEMP value on your EDAN Medical Equipment (for T2A, F3000 and TH module), it could be due to a bad connection of the wire between the TEMP module (T2A, F3000 and TH module) and the monitor, damage to the TEMP module, damage to the TEMP probe, or damage to the main control board. Check the connection and reconnect the connecting wire. If the malfunction continues, replace the connecting wire, the TEMP module, the TEMP probe, or the main control board.
Why is the trace blurred, tilted, or blank on the recording paper of my EDAN Medical Equipment?
If the trace on the recording paper of your EDAN Medical Equipment is blurred, tilts, or is blank, it may be due to inexact loading of the recording paper, the two screw nuts on the print head are not adjusted to balance, or recording head failure. Load the recording paper exactly. Adjust the screw nuts. If the issue continues, replace the recording head.
Why do the fuses burn out when I switch on my EDAN Medical Equipment?
If the fuses burn out when you switch on your EDAN Medical Equipment, this indicates a short circuit of the power or other parts. Switch on the monitor for further check.
What causes disabled operation or measurement functions on EDAN Medical Equipment?
If an operation or measurement function is disabled on your EDAN Medical Equipment, it could be due to main control board or corresponding component damage. Examine the main control board and the corresponding components.
What to do if the rotary knob on my EDAN Medical Equipment isn't working?
If turning the rotary knob on your EDAN Medical Equipment produces no reaction, it could be due to a bad connection of the wire between the rotary knob and main control board, rotary knob switch damage, or main control board failure. Check the connection and reconnect the connecting wire. If that doesn't resolve the issue, replace the rotary knob or the main control board.
Explains the manual's purpose and user responsibilities regarding copyright and intellectual property.
Outlines EDAN's responsibility for equipment safety and performance under specific conditions.
Defines key safety terms like WARNING, CAUTION, and NOTE used throughout the manual.
Details EDAN's one-year warranty, service quality, and limitations.
Outlines the steps for submitting a warranty claim, including form completion and part return.
Provides EDAN's contact details for inquiries about maintenance, specifications, or malfunctions.
Introduces the service manual as a guide for maintenance and corrective procedures for the iM3 monitor.
Provides classification information for the iM3 monitor based on international safety standards.
Lists essential precautions for operating and servicing the monitor to prevent injury.
Explains various symbols used on the iM3 monitor and their meanings.
Specifies the required temperature, humidity, and altitude conditions for operating and storing the monitor.
Lists the electrical specifications, including operating voltage, frequency, input current, and fuse type.
Details critical safety requirements for power outlets and connections to prevent electrical hazards.
Provides instructions for physically placing the monitor on a flat surface or mounting it.
Explains how to properly connect the monitor to the AC power source using the provided cable.
Outlines general checks, including visual inspection and power-on tests, to ensure the monitor is functioning correctly.
Details procedures for testing the functional performance and accuracy of the monitor's measurements.
Describes procedures for performing electrical safety tests to ensure patient and equipment safety.
Provides guidance on general cleaning and maintenance procedures for the monitor.
Details how service engineers can access factory maintenance settings and perform various updates or tests.
Explains how to activate the monitor's demonstration mode for showcasing its features.
Guides users on selecting or saving factory or custom configurations for the monitor.
Outlines the steps for configuring wired or Wi-Fi network settings, including IP address assignment.
Describes how to set and synchronize the monitor's system time and date.
Presents a block diagram illustrating the system architecture and component connections of the iM3 monitor.
Identifies and describes the various physical ports and connectors on the iM3 monitor.
Lists common machine failures, their possible causes, and recommended solutions for the iM3 monitor.
Details issues related to the monitor's display, including character display and screen blackouts, with troubleshooting steps.
Covers problems with user interface elements like buttons, touch screen, and rotary knob, providing solutions.
Addresses issues with the printer, such as no paper output, blurred traces, or paper jams.
Lists problems related to network connectivity, including inability to connect to Wi-Fi or wired networks.
Explains troubleshooting steps for power-related issues, such as blown fuses.
Describes issues with audio or visual alarms not activating and provides solutions.
Covers problems with specific parameter measurements like NIBP and SpO2, including communication stops and inaccuracies.
Lists the necessary tools for disassembling and servicing the iM3 monitor.
Provides a step-by-step guide to disassembling the main components of the iM3 monitor.
Details the process of disassembling the front housing of the iM3 monitor to access internal components.
Guides the disassembly of the rear housing of the iM3 monitor.
Details the process of removing the middle frame assembly from the iM3 monitor.
Outlines the disassembly of various plug-in modules for the iM3 monitor.
General| SpO2 | Yes |
|---|---|
| NIBP | Yes |
| Temperature | Yes |
| Respiration | Yes |
| Pulse Rate | Yes |
| Display Size | 8.4 inches |
| Battery | Rechargeable lithium-ion |
| Battery Life | Up to 4 hours |
| Storage Temperature | -20 ~ 60 ℃ |
To Next Page
