Endress+Hauser Proline Promag 50 User Manual

BA046D/06/en/10.03
50097090
Valid as of software version:
V 1.06.XX (amplifier)
V 1.03.XX (communication)
PROline promag 50
Electromagnetic
Flow Measuring System
Operating Instructions

Endress+Hauser Proline Promag 50 Specifications

General

Device Type	Electromagnetic flowmeter
Housing Material	Aluminum, stainless steel
Measuring Principle	Electromagnetic
Measurement Range	0 to 12 m/s
Accuracy	±0.5% of the measured value
Process Temperature	-40 to +130 °C
Process Pressure	Up to 16 bar
Output Signal	4 to 20 mA
Digital Communication	HART, Profibus
Power Supply	24 V DC
Degree of Protection	IP67
Process Connection	Flange
Lining Material	PTFE
Electrode Material	Hastelloy
Material	Stainless steel

Summary

Safety Instructions

1.1 Designated Use

Specifies the intended application and limitations of the measuring device.

1.2 Installation, Commissioning and Operation

Important notes regarding installation, commissioning, and operation.

1.3 Operational Safety

Guidelines for ensuring safe operation and handling of the device.

Identification

2.1 Device Designation

Details on the naming and components of the Promag 50 system.

2.1.1 Nameplate of the Transmitter

Information found on the transmitter's identification plate.

2.1.2 Nameplate of the Sensor

Information found on the sensor's identification plate.

Installation

3.1 Incoming Acceptance, Transport and Storage

Procedures for receiving, moving, and storing the device.

3.2 Installation Conditions

Environmental and site requirements for installation.

3.2.2 Mounting Location

Recommendations for selecting an appropriate installation site.

3.3 Installation Instructions

Step-by-step procedures for installing sensors.

3.3.1 Installing the Promag W Sensor

Specific instructions for installing the Promag W sensor.

3.3.2 Installing the Promag P Sensor

Specific instructions for installing the Promag P sensor.

3.3.3 Installing the Promag H Sensor

Specific instructions for installing the Promag H sensor.

Wiring

4.1 Connecting the Remote Version

Instructions for connecting remote transmitter and sensor units.

4.1.1 Connecting Promag W / P / H

Wiring details for Promag W, P, and H sensors to transmitters.

4.2 Connecting the Measuring Unit

Procedures for connecting the transmitter unit.

4.2.1 Connecting the Transmitter

Steps for connecting power and signal cables to the transmitter.

4.2.2 Terminal Assignment

Mapping of terminals to functions and outputs.

4.2.3 HART Connection

How to establish a HART communication connection.

4.3 Potential Equalisation

Methods for ensuring equal electrical potential.

4.3.2 Special Cases

Procedures for potential equalisation in non-standard conditions.

Operation

5.1 Display and Operating Elements

Description of the device's display and push buttons.

5.2 Brief Operating Instruction to the Function Matrix

Guide to navigating and using the device's function matrix.

5.2.1 General Notes

Important notes on using the function matrix for configuration.

5.3 Error Messages

Information on interpreting and responding to device errors.

5.4 Communication (HART)

Details on communication via the HART protocol.

5.4.3 Universal / Common Practice HART Commands

List of HART commands supported by the Promag 50.

Commissioning

6.1 Function Check

Final checks before starting the measuring device.

6.2 Commissioning

Procedures for setting up and configuring the device.

6.2.1 Switching on the Measuring Device

Procedure for powering on and initial startup of the device.

6.2.2 “Commissioning” Quick Setup Menu

Step-by-step guide for initial device configuration.

6.2.3 Empty-Pipe/Full-Pipe Adjustment

Procedure for adjusting for empty or full pipe conditions.

Maintenance

Exterior Cleaning

Guidelines for cleaning the exterior of the device.

Seals

Information on periodic replacement of seals, especially for Promag H.

Accessories

Trouble-shooting

9.1 Trouble-shooting Instructions

General guide to diagnosing and resolving device faults.

Check the Display

Troubleshooting steps for display-related issues.

Error Messages on Display

Interpreting and resolving error messages shown on the display.

9.2 System Error Messages

Detailed information on system errors and their remedies.

9.3 Process Error Messages

Detailed information on process errors and their remedies.

9.4 Process Errors Without Messages

Troubleshooting for process errors without displayed messages.

9.5 Response of Outputs to Errors

How device outputs react to different error conditions.

9.7 Removing and Installing Printed Circuit Boards

Procedures for safely removing and installing electronic boards.

9.8 Replacing the Device Fuse

Instructions for replacing the device fuse.

Technical Data

10.1 Technical Data at a Glance

Overview of the device's intended applications and operating conditions.

10.1.1 Application

Overview of the device's intended applications and operating conditions.

10.1.2 Function and System Design

Details on the measuring principle and system components.

10.1.3 Input

Specifications for input signals and measured variables.

10.1.4 Output

Details on output signals, load, and switching output.

10.1.5 Power Supply

Information on electrical connections and supply voltage.

10.1.6 Performance Characteristics

Data on accuracy, repeatability, and measurement error.

10.1.7 Operating Conditions

Environmental requirements and installation restrictions.

10.2 Measuring-Tube Specifications

Specifications for measuring tubes, including diameters.

10.3 Dimensions Wall-mounted Housing

Physical dimensions of the wall-mounted housing.

10.4 Dimensions Promag 50 W

Dimensional data for Promag 50 W models.

10.5 Dimensions Promag 50 P

Dimensional data for Promag 50 P models.

10.7 Dimensions Promag 50 H

Dimensional data for Promag 50 H models.

10.8 Process Connections Promag H (DN 40...100)

Details on process connections for Promag H, DN 40-100.