Endress+Hauser SpectraSensors SS2100i-1 User Manual

Name: Endress+Hauser SpectraSensors SS2100i-1
Brand: Endress+Hauser
Rating: 4 (1 reviews)

114 pages

To Next Page

To Previous Page

Table of Contents5
List of Figures9
List of Tables11
Who Should Read this Manual13
General Informational Icons13
Conventions Used in this Manual14
Spectrasensors Overview14
Manufacturer Address14
Firmware Version15
Powering up the Analyzer15
To Power up the Analyzer15
Powering down the Analyzer16
To Power down the Analyzer17
Operating the Analyzer from the Keypad17
Modes Defined19
Mode 1: (Normal Mode)19
Mode 2: (Set Parameter Mode)19
Mode 3: Not Used20
Mode 4: (System Diagnostic Parameters)20
Mode 5: (4-20 Ma Test Mode)20
Mode 6: (Diagnostic Data Download)21
Mode 7: (Measure Port1 Mode)21
Mode 8: (Measure Port2 Mode)22
Mode 9: (Recall Validation Results)22
Mode Test: (Analog Input Test Mode)24
Configuring the Analyzer at Start-Up24
Parameter Setting/Checking Procedure24
Changing Measurement and Control Parameters25
Table 2-1 Typical Values for Parameter Setpoints25
To Change Parameters in Mode 229
Measurement and Control Parameters Defined29
Way Com Port30
4-20 Ma Alarm Action30
4-20 Ma Val Action30
AI 4 Ma Value31
AI 20 Ma Value31
AI Pressure Input31
AO 4 Ma Value31
AO 4-20 Ma Test32
AO 20 Ma Value32
Baud Rate32
Calculate Dew Point33
Cancel Val Alarms33
Concentration Unit33
Table 2-2 Default Conversion Factors34
Custom Precision35
Daily Validation35
Dew Point Method35
DO Alarm Setup36
Table 2-3 Assignable Alarm Functionality36
General Alarm DO38
High Alarm Setpoint38
Keypad Watchdog38
Logger Rate39
Low Alarm Setpoint39
Modbus Address39
Modbus Mode39
Operator Parameter01 to Operator Parameter2040
To Access the Operator Parameter Section40
Peak Tracking42
Pipeline Pressure42
Pressure Unit42
RATA (Relative Accuracy Test Audit)43
RATA Multiplier43
RATA Offset43
Set Time - Day43
Set Time - Hour44
Set Time - Minute44
Set Time - Month44
Set Time - Year44
Start Validation45
Temperature Unit45
Update RATA45
Val 1 Concentration46
Val 2 Concentration46
Val Attempts46
Val Auto Dumpspectrm47
Validation Allowance47
Validation Wait Time47
Val Interval48
Val Perm Constant Kp48
Val Perm Rate Rp48
Val Start Time49
Zero Val Tolerance49
Adjusting Analyzer Reading to Match Specific Standard(S)49
To Adjust the Analyzer Reading51
Application Examples52
To Set Manual Dual Validation52
To Set Semi-Automatic Single or Dual Validation52
Automatic Single or Dual Validation53
Validating the Analyzer54
To Validate Automatically54
To Validate Semi-Automatically54
To Validate Manually54
Scaling and Calibrating the Current Loop Signal55
To Scale the Current Loop Signal55
Warnings56
Alarms56
System Faults56
User Alarms57
Assignable Alarm58
Validating the Analyzer58
To Validate Automatically58
To Validate Semi-Automatically58
To Validate Manually58
Calibrating the Analyzer59
Switching Stream Compositions59
To Measure Stream 159
To Measure Stream 260
3: Serial Port Communications61
Receiving Serial Data (Customer Port Output)61
To Launch Hyperterminal61
Mode 1 Data String61
To Capture and Save Data from the Serial Port65
To Read Diagnostic Data with Hyperterminal65
Mode 6 Data66
Viewing Diagnostic Data with Microsoft Excel68
To Import the Data File into Excel68
Modbus Communications Protocol72
Framing/Protocol72
Functions72
Reading/Writing in Daniel Modbus Mode72
Reading/Writing in Gould Modbus Mode72
Endianness73
To Enable Modbus Communications73
Addressing74
Table 3-1 Modbus Register Map75
Modbus Accessible Parameter Definitions80
Table 3-2 Assignable Alarm Functionality80
Table 3-3 Status Flags87
Table 3-4 ASCII Character Map88
4: Ethernet Communications91
Configuring the Built-In Ethernet Port91
To Configure the Built-In Ethernet Port with Telnet91
To Configure the Built-In Ethernet Port with the Web Manager92
Network Mode95
Automatic IP Address Configuration95
To Assign an IP Address Automatically95
Static IP Address Configuration95
To Assign an IP Address Manually96
Ethernet Configuration96
To Specify How Data will be Transmitted96
Channel Connection97
To Configure a Channel's TCP Settings97
General Information for Configuring Ethernet99
Appendix A: Troubleshooting101
Contamination101
Excessive Sampling Gas Temperatures and Pressures101
Peak Tracking Reset Procedure101
To Reset the Peak Tracking Function102
Instrument Problems103
Table A-1 Potential Instrument Problems and Their Solutions103
Service Contact104
Before Contacting Service105
Disclaimers105
Index107

Brand	Endress+Hauser
Model	SpectraSensors SS2100i-1
Category	Measuring Instruments
Language	English

Endress+Hauser SpectraSensors SS2100i-1 User Manual

Table of Contents

Other manuals for Endress+Hauser SpectraSensors SS2100i-1

Questions and Answers:

Endress+Hauser SpectraSensors SS2100i-1 Specifications

Related product manuals