EPSON Stylus CX7300/CX7400/DX7400/NX200/TX200 series/SX200 series/Stylus CX8300/CX8400/DX8400/NX400/TX400 series/SX400 series Revision C
PRODUCT DESCRIPTION Specification for Each Function 37
Confidential
1.7.3.4 Operating Specifications during Connecting DSC 1.7.3.5 EXT.I/F (USB Host) Specifications for Connecting DSC
Table 1-37. Operations during Connecting DSC
Operation Specifications
Connecting
DSC
(print start)
When a DSC is connected as described in “ 1.7.3.3 General Operation
Procedure ( p. 36 ) ” Step 3-(1), CX8300/TX400 series displays USB Direct
Print or PictBridge logo on the LCD. On the CX7300/TX200 series, the
Power LED flashes and “P” is displayed on the 7 seg LED.
Canceling
printing
A print job can be canceled from the DSC.
The [Stop/Clear setting] button on the CX8300/TX400 series, and the [Stop]
button on the CX7300/TX200 series also cancels the print job.
After printing
is completed
When performing memory card direct print after printing from a DSC, the
USB cable connecting the DSC must be disconnected from the printer in
advance.
Exclusion
control
Print settings made on both the DSC and the printer can become impossible
settings for the printer due to unsupported combination of paper type, paper
size and layout. In such case, the print settings are automatically changed as
follows.
USB Direct Print
The selected paper type is maintained, and the paper size and layout
settings are changed to the default for the selected paper type.
PictBridge
The settings made on the DSC are maintained. Any print setting items that
are not specified by the DSC are changed in accordance with the DSC
settings. When the paper type is changed, changed to Prem. Glossy, when
the paper size is changed, changed to 4x6 size. And when the layout is
changed, changed to Borderless layout.
Table 1-38. Operations when USB Cable is Connected/Disconnected
Printer status Connecting Disconnecting
Standby When the printer detects a DSC
connected, it goes into the camera
direct mode. If the printer failed to
recognize the DSC normally, the
printer displays a camera direct error.
When the DSC is disconnected after
it is normally recognized by the
printer, the printer returns to the
standby mode.
An error is
occurring
The printer does not go into the
camera direct mode except when the
error is memory card-related error,
Index Sheet error, or Ink low error.
When a camera direct error has
occurred, the printer recovers from
the error and returns to the previous
state (the state before the camera is
connected). If the error occurs for the
camera connected before the printer
is turned on, the printer returns to the
initial state after the power-on.
Panel power
save mode
Same as when the printer is in
standby mode.
The printer does not recover from the
power save mode. When any button
except the Power button is pressed,
the printer returns to the camera
direct mode. If the printer detect no
camera at this time, it returns to the
previous state (the state before the
camera is connected)
Table 1-39. Handling Print Job Requirement from PC when Connecting DSC
Requirement
from PC
EXT.IF (USB Host) DSC Connecting Status
Normally Connected Camera Direct Error is Occurring
Print job Returns “Busy” to the PC.
Cancels the error state and performs
the job.
Scan job Returns “Busy” to the PC.
Cancels the error state and performs
the job.
Read
memory card
Allows the access. Allows the access.
Write
memory card
Not allows the access. Notifies the PC
that the operation is not available.
Allows the access.
Maintenance
Returns “Busy” to the PC.
Cancels the error and carries out the
required task.
To Next Page
Loading...
Need help?
General