evertz 5601AC02

To Next Page

To Previous Page

Model 5601ACO2 Automatic Changeover Unit

Page 4-12 Revision 1.2 TECHNICAL DESCRIPTION

4.6.5. Upgrade

5) Upgrade – enters an upgrade mode for firmware upgrades. If entered you will be prompted again

to be sure you wish to do an upgrade. See section

4.5.4 above for details on how to complete the

upgrade.

Main Page

Table of Contents7
Overview11
Figure 1-1: 5601ACO2 Block Diagram13
How to Use this Manual14
Figure 1-2: Front View of Frame14
Installation15
Rear Panel15
Coaxial Connections15
Figure 2-1: 5601ACO2 Rear Panel15
Balanced AES, DARS and Analog Audio Connections16
Linear Time Code, Syncro and GPIO Connections16
Table 2-1: DARS/AES/ANALOG Terminal Strip Pin Definitions16
Table 2-2: AUX I/O Pin Definitions16
Ethernet Connections17
Table 2-3: ACO CTRL/STATUS and MSC GPIO Terminal Strip Pin Definitions17
Table 2-4: Standard RJ45 Wiring Colour Codes17
Power Connections18
Mounting18
Power Requirements18
5601Msc Connections19
Figure 2-2: Redundant Master Clock/Spg with Auto Changeover System Diagram19
Sync Outputs20
10 Mhz Output20
Word Clock Output20
Unbalanced DARS AES1 and AES2 Outputs20
Balanced DARS, AES1, AES2 and Analog Audio Outputs20
Video Test Signal Generator Outputs21
LTC and GPIO Connections21
Synchronizing the Menu Settings of the Two 5601MSC Units22
Connecting the General Purpose Inputs and Outputs22
Figure 2-3: Typical GPI Circuitry22
Figure 2-4: GPO1 Output Circuitry23
Figure 2-5: GPO2 Output Circuitry23
How to Operate the Automatic Changeover25
An Overview of the Status Indicators25
Operating Mode Indicators25
Figure 3-1: Model 5601ACO2 Front Panel25
Input Indicators26
ACO GPI Indicators26
Power Supply Indicators26
Front Panel Control26
Automatic Changeover Mode27
Manual GPI Changeover Mode27
Figure 3-2: Front Panel & Card Edge Control27
Manual Switch Changeover Mode28
Front Door Button: Recent Event Trigger28
Dip Switches28
GPI Input Mode28
Table 3-1: DIP Switch Functions28
Table 3-2: GPI Input Mode Switch Settings29
Table 3-3: Single GPI Mode Operation29
Table 3-4: Dual GPI Mode Operation29
Changeover Rate30
Bank Priority30
Change Limiting30
Table 3-5: Changeover Rate Switch Settings30
Table 3-6: Bank a Priority Switch Settings30
Table 3-7: Change Limiting Switch Settings30
Gpo Tally Outputs31
Technical Description33
Auto Changeover Switch Criteria33
Change Limiting Operation33
One Change Mode34
Dual Change Mode34
Unlimited Change Mode34
Switching Decision Tree35
Figure 4-1: 5601ACO2 Switching Logic35
Specifications36
LTC Outputs36
Coaxial Inputs and Outputs36
Balanced DARS, AES1, AES2 and Analog Audio Inputs and Outputs36
ACO General Purpose Inputs and Outputs36
MSC General Purpose Inputs and Outputs37
Changeover Conditions37
Ethernet37
Electrical37
Physical37
Upgrading the Firmware38
Overview38
Terminal Program Setup38
Initiating Firmware Upgrade Mode from the Terminal Program39
Uploading the New Firmware39
Completing the Upgrade40
Serial Port Configuration and Status40
Network Configuration41
SNMP Configuration41
Voting Control42
Show Status43
Upgrade44
Vistalink Configuration and Control45
Connecting the 5601ACO2 to VISTA LINK45
Installing VISTA LINK45
Using Vistalink46
To Configure the 5601ACO246
General Control Settings46
Figure 5-1: Vistalink46
Configuration - General Control46
Monitoring the 5601ACO2 Using the General Status Tab47
Figure 5-2: Vistalink Monitoring - General Status47
Configuring the Voting Control48
Global Control Parameters48
Figure 5-3: Vistalink48
Monitoring - Voting Control48
General Parameters49
Analog TG Voting Parameters49
HD SDI TG Voting49
Analog Sync Voting49
DARS Voting49
LTC Voting49
GPO Voting50
Monitoring the GPO Status50
GPO Status Tab50
Figure 5-4: Vistalink Monitoring - GPO Status50
5601ACO2 Fault Trap Controls51
Setting the Analog Faults51
Figure 5-5: Vistalink Monitoring - Analog Faults51
Setting the 3G HD SDI TG Faults52
Figure 5-6: Vistalink Monitoring - 3G HD SDI Faults52
Setting the AES DARS Faults53
Setting the LTC Faults53
Figure 5-7: Vistalink Monitoring - AES DARS Faults53
Setting the MSC GPO Faults54
Figure 5-8: Vistalink54
Figure 5-9: Vistalink54
Monitoring - LTC Faults54
Monitoring - MSC GPO Faults54
Configuring the Faults Tab55
Figure 5-10: Vistalink Monitoring - Faults55

evertz 5601AC02 - Upgrade

Table of Contents

Related product manuals