Extron electronics SSP 200 - Page 83

SSP 200 • SIS Configuration and Control 75
Command SIS Command
(Host to Device)
Response
(Device to Host)
Additional Description
Input Selection
Select audio input
X4@$ AudX4@]
View audio input
$
Verbose modes 2/3
X4@]
AudX4@]
Set EXP input
assignment
EEX4#SSP} SspEX4#]
View EXP input
assignment
EESSP}
Verbose modes 2/3
X4#]
SspEX4#]
Set EXP input channel
pair
EPX4$SSP} SspPX4$]
View EXP input channel
pair
EPSSP}
Verbose modes 2/3
X4$]
SspPX4$]
View audio input source
33I
Verbose modes 2/3
SrcFormat•X4%•Sampling•X4^•EnChan•X4&]
Inf33SrcFormat•X4%•Sampling•X4^•EnChan•X4&]
View audio signal
presence (selected input)
E0LS}
Verbose modes 2/3
X4*]
In00•X4*]
View input HDCP status
EIHDCP}
Verbose modes 2/3
X4(]
HdcplX4(]
Set HDCP authorization
EEX5)HDCP} HdcpEX5)]
View HDCP
authorization status
EEHDCP}
Verbose modes 2/3
X5)]
HdcpEX5)]
View incoming line count
34I
Verbose modes 2/3
Example:
<Total Lines>*<Vfreq>*<Hfreq>*<Hcount>]
Inf34*<Total Lines>*<Vfreq>*<Hfreq>*<Hcount>]
Inf34*1080*60.016788*67.498636*1920]
KEY:
X4@
=
Input number: 1 to 5
X4#
=
EXP assignment (HDMI and analog inputs are unavailable for EXP assignment):
0 = EXP off (default) 2 = Input 2 3 = Input 3 4 = Input 4
X4$
=
EXP input channel pair:
1 = EXP Input 1 & 2 2 = EXP Input 3 & 4 3 = EXP Input 5 & 6 4 = EXP Input 7 & 8
5 = EXP Input 9 & 10 6 = EXP Input 11 & 12 7 = EXP Input 13 & 14 8 = EXP Input 15 & 16
X4%
=
Source format:
0 = Not present 1 = Analog 2 = PCM 3 = Dolby Digital/EX 4 = Dolby Digital Plus
5 = Dolby Digital Plus ATMOS 6 = Dolby TrueHD 7 = Dolby TrueHD ATMOS 8 = DTS or DTS 96/24
9 = DTS‑ES (96/24, Matrix, or Discrete) 10 = DTS‑HD High Resolution Audio 11 = DTS‑HD Master Audio
12 = DTS Express 13 = DTS:X
X4^
=
Decoded Sampling Rate:
0 = None 1 = 32 kHz 2 = 44.1 kHz 3 = 48 kHz 4 = 88.2 kHz 5 = 96 kHz
6 = 176.4 kHz 7 = 192 kHz
X4&
= Source Encoded Channels (Front, Center, Surround, Back, Subwoofer, Height):
0 = None 1 = 1.0 2 = 1.1 3 = 2.0 4 = 2.1 5 = 3.0
6 = 3.1 7 = 4.0 8 = 4.1 9 = 5.0 10 = 5.1 11 = 6.0
12 = 6.1 13 = 7.0 14 = 7.1
X4*
=
Signal Status: 0 = Signal not detected 1 = Signal detected
X4(
=
Input HDCP status: 0 = No source is detected 1 = Source is detected with HDCP 2 = Source detected without HDCP
X5)
=
Enable or Disable: 0 = Disable 1 = Enable (default)