Fike ECS Series - Page 23

66 pages

Save Page as PDF

To Next Page

To Previous Page

ECS Series Manual — P/N LS10262-001FK-E:A 3/3/2021 23

Installing the FIK-NVCM Device Installation

Figure 4.6 Wiring Harness Connection for the FIK-NVCM to FCP-2100ECS

Figure 4.7 Connection between FIK-EMG and Two FIK-SW24s

Main Page

Table of Contents5
Section 1: Overview7
Optional Accessories7
ECS Features7
Terms Used in this Manual8
Section 2: Agency Listings, Approvals, and Requirements10
Federal Communications Commission (FCC)10
Underwriters Laboratories (UL)10
1: Requirements for All Installations10
2: Requirements for Central Station Fire Alarm Systems10
3: Requirements for Local Protected Fire Alarm Systems11
4: Requirements for Remote Station Protected Fire Alarm Systems11
5: Requirements for the Installation of Carbon Monoxide (CO) Detection and Warning Equipment, NFPA 72011
Section 3: Installation12
Environmental Specifications12
Wiring Specifications12
Electrical Specifications14
Installing ECS Series Cabinets15
1: Preventing Water Damage15
2: Surface Mounting the FCP-300ECS, FCP-2100ECS or FIK-LOC Cabinet15
3: Surface Mounting the FIK-LOC Cabinet16
4: Surface Mounting the FCP-300ECS Cabinet17
5: Surface Mounting the FCP-2100ECS or FIK-LOC2100 Cabinet17
6: Surface Mounting Instructions18
Section 4: Device Installation20
Connecting AC Power and Batteries20
Installing the FIK-NVCM20
1: FIK-NVCM Board Layout20
2: Installing and Connecting the FIK-EMG to the FIK-SW2421
3: FIK-NVCM Fiber Modules24
4: Installing the Microphone24
Installing the FIK-50W25
1: FIK-50W Board Layout26
2: Mounting the FIK-50W26
3: Wiring Specifications27
4: Speaker Wiring28
5: VBUS Wiring29
6: SBUS Wiring30
7: Connecting AC Power31
8: Backup Battery for FIK-50W32
9: Calculating Current Draw and Standby Battery33
Installing the FIK-INT50W34
1: Board Layout & Mounting34
2: Wiring to a FACP36
3: VBUS Wiring37
4: Setting the Device Address37
Speaker Wiring37
1: Calculating Current Draw and Standby Battery37
Installing the FIK-125W38
1: FIK-125W Board Layout38
2: Mounting the FIK-125W39
3: Mounting the FIK-125WBD Board Only39
4: Wiring Specifications40
5: Speaker Wiring41
6: VBUS Wiring43
7: SBUS Wiring43
8: Connecting AC Power44
9: Backup Battery for FIK-125W45
10: Calculating Current Draw and Standby Battery45
Installing the FIK-DUAL50W46
1: FIK-DUAL50W Board Layout47
2: Mounting the FIK-DUAL50W47
3: Mounting the FIK-DUAL50WBD Board Only48
4: Wiring Specifications49
5: Speaker Wiring50
6: VBUS Wiring52
7: SBUS Wiring54
8: Setting the FIK-DUAL50W Mode55
9: Test Switch Use55
10: Connecting AC Power55
11: Backup Battery for FIK-DUAL50W56
12: Calculating Current Draw and Standby Battery56
Installing the FIK-50WBU56
1: FIK-DUAL50W Board Layout57
2: Installing the FIK-50WBU57
Installing the FIK-CE458
Installing the FIK-RVM59
1: FIK-RVM Board Layout59
2: Wiring the FIK-RVM60
3: Installing the Microphone62
4: to Remove the FIK-RVM63
Addressing SBUS Devices63

Fike ECS Series - Page 23

Table of Contents

Related product manuals