Why is the basket symbol not lit on Franke F3D3P?
If the basket symbol on your Franke Dispenser isn't lighting up, it means the dispenser lane is switched off. Press the ON/OFF button for 4 seconds until the button LEDs light up.
Why individual lanes of my Franke F3D3P Dispenser will not turn on?
If individual lanes won't turn on, ensure the main power is on by pressing the power switch to the 'ON' position. The rocker switch should illuminate. Allow 3 hours for cool-down before adding product. Also, check if the machine is plugged into a 120VAC or 230V/50Hz outlet as per the data plate and the main power switch is on. Finally, make sure you hold the LANE ON/OFF touch pad long enough (four seconds) until the two green lights come on.
Why won't the freezer door close on my Franke Dispenser?
If the freezer door on your Franke Dispenser isn't closing properly, it might be because the hopper(s) is/are not correctly engaged in the drum hub. Press the hopper into the appliance, turning the drum at the handle if necessary.
Why green 'Ready' lights don't come on my Franke F3D3P?
If the green 'Ready' lights don't come on, the lane may be turned off. Press the On/Off 'Power' button to turn on the lane. It could also be that the desired load size has not been achieved, in that case, see the section addressing when the green 'Reset' button lights are flashing steadily.
What does 'Low Product Warning' mean on my Franke F3D3P?
The 'Low Product Warning' indicates that you should add fries to the hopper, or continue dispensing until Error Message 4 appears.
Why I am unable to change load size on Franke Dispenser?
You are unable to change the load size using the control panel if the fill process has not completed. Load size can be changed when the green load ready lights are on and 'Ready' is on the display.
Why won't the drum turn on my Franke F3D3P?
If the drum on your Franke Dispenser isn't turning, it could be due to: * An empty hopper. If the screen displays the error message Err04 and the Action–3 [Reset] button is flashing, fill the hopper with fries and press [Reset] to begin the filling process. * Fries baked together forming a "bridge" in the hopper. If the screen displays the error message Err04 and the ACTION–3 [Reset] button is flashing, shake the hopper to redistribute the fries and break up the bridge. Proceed carefully so as not to break the fries, then press [Reset] to start the filling process.
What does low product warning mean on Franke Dispenser?
If you see the [Low product warning] error message on your Franke Dispenser, it means: * The hopper has a low filling level (only 3–4 fillings left). Refill the hopper with fries. Be aware that if the machine dispenses until the hopper is completely empty, the filling process will be aborted, and error message Err04 will appear. * Frozen fries have created a hollow space around the sensor in the hopper. Shake the hopper to redistribute the fries and close the hollow space, being careful not to break the fries.
Why is the reset button flashing on my Franke F3D3P?
If the ACTION-3 [Reset] button on your Franke Dispenser is flashing, it indicates: * The filling process was prematurely aborted. Press the [Reset] button to restart the filling process. * Fries in the hopper have formed a "bridge." Shake the hopper to redistribute the fries, carefully breaking up any clumps.
What to do if Franke F3D3P shows Err04 and won't dispense?
If your Franke Dispenser isn't dispensing and shows error message Err04, it means: * The hopper is empty. You should fill the hopper with fries and press the [Reset] button to begin the filling process. * Fries are baked together in the hopper forming a hard "bridge". You should shake the hopper to redistribute the fries and break up the clumps, carefully so as not to break the fries. If necessary, remove very hard clumps, then press [Reset] to start the filling process.
Guide to identifying different F3D3 models based on features.
Guide to diagnosing issues and understanding error codes.
Procedures for accessing and modifying unit settings.
Essential instructions, warnings, and tools for service.
Step-by-step guide for replacing the freezer door gasket.
Procedure for replacing the automation assembly.
Steps to replace the drum rotor motor.
Adjusting the sensitivity of the low product sensor.
Instructions for reversing door hinges and swing direction.
Critical restrictions and warnings for servicing propane models.
Routine maintenance procedures for the refrigeration system.
Procedure for replacing the condenser fan motor.
Instructions for accessing factory-level 1 setup parameters.
Guide to accessing and modifying factory-level 3 parameters.
Details the limited warranty coverage for new equipment.
Contact details for Franke technical support and service network.
Step-by-step questions to diagnose service issues.
Lists common error messages and required actions.
Lists parts for access panels, filters, and casters.
Lists loose component parts for freezer and dispensing.
Lists parts for control panel and master board.
Lists electrical components mounted on DIN rail.
Lists parts for the load cell assembly.
Wiring diagram for 120-volt operation.
Wiring diagram for 230-volt operation.
Quick guide to control panel functions and components.
Procedures for accessing customer-level settings and parameters.
Step-by-step procedure for calibrating the load cell.
Basic introduction to field service for F3D3 series.
Recommended parts for ensuring first-trip fixes.
Step-by-step guide for replacing the load cell.
Procedure for replacing the door-closing spring.
Procedure for replacing the automation assembly.
Steps for replacing the main control board.
Procedure for replacing the power cord.
Adjusting the sensitivity of the low product sensor.
Instructions for reversing door hinges and swing direction.
Aligning the automation assembly for proper fit.
Aligning the fry hopper for proper installation.
Reconfiguring control board for backup temperature display.
Critical restrictions and warnings for servicing propane models.
Routine maintenance procedures for the refrigeration system.
Procedure for replacing the condenser fan motor.
Guide to checking refrigerant pressure and detecting leaks.
Steps to replace the condensing unit.
General| Model | F3D3P |
|---|---|
| Brand | Franke |
| Material | Stainless Steel |
| Capacity | 3 liters |
| Installation | Countertop |
| Voltage | 220-240 V |
| Power Supply | Electric |
| Type | Dispenser |
To Next Page
