Why won't the filler doors open on my Franke F3D3P Dispenser?
If the filler doors on your Franke Dispenser aren't opening to dispense fries, wait for the BASKET symbol to light up. Once it does, the fries will be dispensed.
Why can't I change the load size on my Franke F3D3P?
You can't change the load size on the Franke Dispenser operator panel if the filling process isn't finished yet. The filling process is complete when the BASKET symbol LEDs light up and [Ready] appears on the screen. Then you can change the load size.
What to do if filler doors won't close on Franke F3D3P Dispenser?
If the filler doors on your Franke Dispenser aren't closing after dispensing fries, it's likely that fries are jammed in the filler doors. Remove all fries from the filler doors.
What to do if Franke F3D3P shows Error 4 – Hopper Empty?
If your Franke Dispenser displays Error 4, it means the hopper is empty. Fill it with fries. Also, check the hopper for any frozen fries that may have formed a bridge. After filling or clearing any blockages, press the flashing button under the word 'Reset'.
Why won't my Franke F3D3P Dispenser dispense and shows Err04 error?
If your Franke Dispenser isn't dispensing and displays error code Err04, it's likely because the hopper is empty or a clump of fries is blocking the hopper rotor. Fill the hopper with fries, and break up any clumps. If necessary, remove the clumps and replace them with loose fries. Then, press the 'Reset' button to restart the drum and begin the fill cycle.
Guide to identifying different F3D3 models based on features.
Guide to diagnosing issues and understanding error codes.
Procedures for accessing and modifying unit settings.
Essential instructions, warnings, and tools for service.
Step-by-step guide for replacing the freezer door gasket.
Procedure for replacing the automation assembly.
Steps to replace the drum rotor motor.
Adjusting the sensitivity of the low product sensor.
Instructions for reversing door hinges and swing direction.
Critical restrictions and warnings for servicing propane models.
Routine maintenance procedures for the refrigeration system.
Procedure for replacing the condenser fan motor.
Instructions for accessing factory-level 1 setup parameters.
Guide to accessing and modifying factory-level 3 parameters.
Details the limited warranty coverage for new equipment.
Contact details for Franke technical support and service network.
Step-by-step questions to diagnose service issues.
Lists common error messages and required actions.
Lists parts for access panels, filters, and casters.
Lists loose component parts for freezer and dispensing.
Lists parts for control panel and master board.
Lists electrical components mounted on DIN rail.
Lists parts for the load cell assembly.
Wiring diagram for 120-volt operation.
Wiring diagram for 230-volt operation.
Quick guide to control panel functions and components.
Procedures for accessing customer-level settings and parameters.
Step-by-step procedure for calibrating the load cell.
Basic introduction to field service for F3D3 series.
Recommended parts for ensuring first-trip fixes.
Step-by-step guide for replacing the load cell.
Procedure for replacing the door-closing spring.
Procedure for replacing the automation assembly.
Steps for replacing the main control board.
Procedure for replacing the power cord.
Adjusting the sensitivity of the low product sensor.
Instructions for reversing door hinges and swing direction.
Aligning the automation assembly for proper fit.
Aligning the fry hopper for proper installation.
Reconfiguring control board for backup temperature display.
Critical restrictions and warnings for servicing propane models.
Routine maintenance procedures for the refrigeration system.
Procedure for replacing the condenser fan motor.
Guide to checking refrigerant pressure and detecting leaks.
Steps to replace the condensing unit.
Guide to identifying different F3D3 models based on features.
Guide to diagnosing issues and understanding error codes.
Procedures for accessing and modifying unit settings.
Essential instructions, warnings, and tools for service.
Step-by-step guide for replacing the freezer door gasket.
Procedure for replacing the automation assembly.
Steps to replace the drum rotor motor.
Adjusting the sensitivity of the low product sensor.
Instructions for reversing door hinges and swing direction.
Critical restrictions and warnings for servicing propane models.
Routine maintenance procedures for the refrigeration system.
Procedure for replacing the condenser fan motor.
Instructions for accessing factory-level 1 setup parameters.
Guide to accessing and modifying factory-level 3 parameters.
Details the limited warranty coverage for new equipment.
Contact details for Franke technical support and service network.
Step-by-step questions to diagnose service issues.
Lists common error messages and required actions.
Lists parts for access panels, filters, and casters.
Lists loose component parts for freezer and dispensing.
Lists parts for control panel and master board.
Lists electrical components mounted on DIN rail.
Lists parts for the load cell assembly.
Wiring diagram for 120-volt operation.
Wiring diagram for 230-volt operation.
Quick guide to control panel functions and components.
Procedures for accessing customer-level settings and parameters.
Step-by-step procedure for calibrating the load cell.
Basic introduction to field service for F3D3 series.
Recommended parts for ensuring first-trip fixes.
Step-by-step guide for replacing the load cell.
Procedure for replacing the door-closing spring.
Procedure for replacing the automation assembly.
Steps for replacing the main control board.
Procedure for replacing the power cord.
Adjusting the sensitivity of the low product sensor.
Instructions for reversing door hinges and swing direction.
Aligning the automation assembly for proper fit.
Aligning the fry hopper for proper installation.
Reconfiguring control board for backup temperature display.
Critical restrictions and warnings for servicing propane models.
Routine maintenance procedures for the refrigeration system.
Procedure for replacing the condenser fan motor.
Guide to checking refrigerant pressure and detecting leaks.
Steps to replace the condensing unit.
General| Model | F3D3P |
|---|---|
| Brand | Franke |
| Material | Stainless Steel |
| Capacity | 3 liters |
| Installation | Countertop |
| Voltage | 220-240 V |
| Power Supply | Electric |
| Type | Dispenser |
To Next Page
