FULTON VMP Series - Page 88

VMP-IOMM-2018-2
Fulton Ltd
Page 80
TROUBLESHOOTING - 6
247/254
Building Technologies Division Basic documentation LMV26... CC1P7547en
30 Error code list 20.04.2016 Error code Diagnostic code Meaning for the LMV26... system Remedy
 Improve EMC
121 # Internal error EEPROM access
Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs repeatedly, replace the unit
122 # Internal error EEPROM access
Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs repeatedly, replace the unit
123 # Internal error EEPROM access
Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs repeatedly, replace the unit
124 # Internal error EEPROM access
Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs repeatedly, replace the unit
125 # Internal error EEPROM read access Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 126 # Internal error EEPROM write access Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 127 # Internal error EEPROM access
Make a reset, repeat last parameterization / check. Restore the parameter set, if error occurs repeatedly, replace the unit
128
0 Internal error EEPROM access - synchronization during initialization
Make a reset; if error occurs repeatedly, replace the unit
129 # Internal error EEPROM access – command synchronization Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 130 # Internal error EEPROM access - timeout Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 131 # Internal error EEPROM access - page on abort Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 132 # Internal error EEPROM register initialization Make a reset; if error occurs repeatedly, replace the unit 133 # Internal error EEPROM access – Request synchronization Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 134 # Internal error EEPROM access – Request synchronization Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 135 # Internal error EEPROM access – Request synchronization Make a reset, repeat last parameterization / check. If error occurs repeatedly, replace the unit 136
1 Restore started
Restore of a backup has been started (no error) New devices require resetting following restore!
for further diagnostic codes for error code 136, refer to error code 137
For measures, refer to error code 137
137 # Internal error – backup / restore 157 (-99) Restore – ok, but backup < data set of current system
Restore successful, but backup data record is smaller than in the current system
239 (-17) Backup – storage of backup in AZL2... faulty
Reset and repeat backup
240 (-16) Restore – no backup in AZL2...
No backup stored in AZL2...
241 (-15) Restore – abortion due to unsuitable product no. (ASN)
Backup has an unsuitable product no. (ASN) and must not be restored
242 (-14) Backup – backup made is inconsistent
Backup is faulty and cannot be transferred back
243 (-13) Backup – data comparison between µCs faulty
Reset and repeat backup
244 (-12) Backup data are incompatible
Backup data are incompatible with the current software version, restore not possible
245 (-11) Access error to parameter Restore_Complete
Reset and repeat backup
246 (-10) Restore – timeout when storing in EEPROM
Reset and repeat backup
247 (-9) Data received are inconsistent
Backup data record invalid, restore not possible
248 (-8) Restore cannot at present be made
Reset and repeat backup
249 (-7) Restore – abortion due to unsuitable burner identification
Backup has an unsuitable burner identification and must not be transferred to the unit