30
Exception Rpts (Phones—CS Phone 1-3)
(cs phone 1: 0103, cs phone 2: 0113, cs phone 3: 0123)
(Default = off) When this setting is on, the panel reports to the central station if the system is not
armed or disarmed at the specified schedule times.
¾
To turn Exception Reports off or on:
With the display showing EXCEPTION RPTS OFF/ON (current setting), press 1 (off) or 2 (on).
The display flashes the entered setting. Press # and the display shows the new setting.
Open/Close Rpts (Phones—CS Phone 1-3)
(cs phone 1: 0104, cs phone 2: 0114, cs phone 3: 0124)
(Default = off) This setting determines whether opening and closing reports are sent to the central
station. When turned on, the panel sends a closing report when the system is armed and an open-
ing report when the system is disarmed.
Note
To use this feature, the
Opening Reports and Clos-
ing Reports settings under
the
REPORTING menu must
be turned on for that parti-
tion.
¾To turn Opening/Closing Reports off or on:
With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press 1 (off) or 2 (on).
The display flashes the entered setting. Press # and the display shows the new setting.
Backup (Phones—CS Phone 1-3)
(cs phone 1: 0105, cs phone 2: 0115, cs phone 3: 0125)
(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) This setting determines whether or not the
panel uses another programmed central station phone number for reporting if attempts with the
first number are unsuccessful.
When Back Up is off, the panel will make up to eight attempts to deliver a report with the pro-
grammed phone number.
When Back Up is set to on, the panel makes up to 16 attempts to deliver the report, alternating
between the programmed phone number and the backup phone number.
CS PHONE 1 is backed up by CS PHONE 2.
CS PHONE 2 is backed up by CS PHONE 1.
CS PHONE 3 is backed up by CS PHONE 1.
¾
To turn Backup off or on:
With the display showing BACK UP OFF/ON (current setting), press 1 (off) or 2 (on). The dis-
play flashes the entered setting. Press # and the display shows the new setting.
SIA/CID Reporting (Phones—CS Phone 1-3)
(cs phone 1: 0106, cs phone 2: 0116, cs phone 3: 0126)
(Default = CID) This setting determines whether the panel uses the SIA or CID (Contact ID)
reporting format for central station communication.
¾
To select SIA or CID reporting:
With the display showing REPORTING FORMAT SIA/CID (current setting), press 1 (for SIA) or
2 (for CID). The display flashes the entered setting. Press # and the display shows the new
setting.
Cellular Backup (Phones—CS Phone 1-3)
(cs phone 1: 0107, cs phone 2: 0117, cs phone 3: 0127)
(Defaults: CS Phone 1=on, CS Phone 2 and 3=off) This setting determines whether the panel
uses cellular communication for reporting if attempts using a landline are unsuccessful.
¾
To turn Cellular Backup off or on:
With the display showing CELLULAR BACKUP, press 1 (for off) or 2 (for on). The display
flashes the entered setting. Press # and the display shows the new setting.
The following describes how to program the phone settings that appear under
PAGER PHONE 1-5.
Phone Number (Phones—Pager Phone 1-5)
(pager 1: 0130, pager 2: 0140, pager 3: 0150, pager 4: 0160, pager 5: 0170)
(Default = none) This setting is used for programming a phone number that communicates to a
pager. Phone numbers can be 1 to 24 digits long and include pauses, a skylink number, and
7-digit PIN number.
To Next Page
Loading...
