31
Note
Call-waiting services should
be disabled to prevent inter-
rupting panel communica-
tion to the pager(s). To
program a dialing prefix that
disables call-waiting, see the
Call Wait Cancel setting
under the menu
PHONE
OPTIONS—GLOBAL
.
To enter pauses, press C.
To enter *, press and hold 7 for about two seconds.
To enter #, press and hold 9 for about two seconds.
¾
To program a Pager Phone Number:
With the display showing PHONE NUMBER _ (or current number), enter the desired pager
phone number. The display flashes the entered number. Press # and the display shows the
new setting.
¾
To delete a Pager Phone Number:
With the display showing PHONE NUMBER (current number), press D. The display shows
PHONE NUMBER _.
High Level Rpts (Phones—Pager Phone 1-5)
(pager 1: 0131, pager 2: 0141, pager 3: 0151, pager 4: 0161, pager 5: 0171)
(Default = on) This setting determines whether the following alarm conditions report to a pager:
• Fire, Police, Auxiliary, and Duress alarms
• No Activity
• Receiver Failure (or jam)
• Tamper conditions, including Zone Tampers and System Tamper (40 incorrect key presses or
touchpad supervisory)
• Entering or exiting Sensor Test mode
• Phone Test
¾
To turn High-Level Reports off or on:
With the display showing HIGH LEVEL RPTS OFF/ON (current setting), press 1 (off) or 2 (on).
The display flashes the entered setting. Press # and the display shows the new setting.
Low Level Rpts (Phones—Pager Phone 1-5)
(pager 1: 0132, pager 2: 0142, pager 3: 0152, pager 4: 0162, pager 5: 0172)
(Default = off) This setting determines whether the following non-alarm conditions report to a
pager:
•Force Armed
• Hardwire Zone Trouble (open or short)
• Supervisory (wireless devices)
• Low Battery (wireless devices)
• Phone Test
• Other non-alarm related conditions
¾
To turn Low-Level Reports off or on:
With the display showing LOW LEVEL RPTS OFF/ON (current setting), press 1 (off) or 2 (on).
The display flashes the entered setting. Press # and the display shows the new setting.
Exception Rpts (Phones—Pager Phone 1-5)
(pager 1: 0133, pager 2: 0143, pager 3: 0153, pager 4: 0163, pager 5: 0173)
(Default = off) This setting determines whether the panel reports to a pager if the system is not
armed or disarmed at the specified schedule times, if open/close reports are turned on.
¾
To turn Exception Reports off or on:
With the display showing EXCEPTION RPTS OFF/ON (current setting), press 1 (off) or 2 (on).
The display flashes the entered setting. Press # and the display shows the new setting.
Open/Close Rpts (Phones—Pager Phone 1-5)
(pager 1: 0134, pager 2: 0144, pager 3: 0154, pager 4: 0164, pager 5: 0174)
Note
To use this feature, the
opening reports and closing
reports settings under the
REPORTING menu must be
turned on for that partition.
(Default = off) This setting determines whether opening and closing reports are sent to a pager.
When turned on, the panel sends a closing report when the system is armed and an opening report
when the system is disarmed.
¾
To turn Opening/Closing Reports off or on:
With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press 1 (off) or 2 (on).
The display flashes the entered setting. Press
# and the display shows the new setting.
To Next Page
Loading...
