GE Interlogix 60-792-01-95R - Page 56

51
Cellular System (Acc. Modules—Bus Devices—Unit ID—Cellular Options
(Default = B) This setting determines the cellular transmission system (A or B) used for cellular
communication. This information is provided by the cellular provider based on installation ZIP
code.
¾
To set the Cellular System:
 With the display showing the desired bus device press 1, (B) or 2 (A). The display flashes
the entered selection. Press # and the display shows the new setting.
The following describes how to program the settings that appear under SNAPCARDS.
Output Programming (Acc. Modules—SnapCards—Output Programming)
(101001—output 1, 101011—output 2, 101021—output 3, 101031—output 4)
(Defaults: Partition Assign = all 1, Configuration Output 1 = 01400, Output 2 = 00410,
Output 3 = 00903, Output 4 = 01003) This setting lets you assign a partition and a 5-digit config-
uration number for each SnapCard relay output. This number determines both which system
event activates the output and the duration or time the output is activated.
1. Partition: the system partition (1 or 2).
2. Configuration number: The combination of a trigger and a response.
Trigger: the event that activates the output point. Trigger events can be partition alarms,
trouble conditions, open sensors, etc. (see Appendix B: Reference Tables).
Response: how the output responds when trigger event occurs (see Appendix B: Reference
Tables).
This section describes how to program each of the output point configurations into the security
panel. The point configuration number is tttrr, where ttt is the trigger number and rr is the
response number.
¾
To assign configuration numbers to SnapCard Relay outputs:
1. With the display showing SNAPCARDS, press #. Then press A or B until the display shows
OUTPUT PROGRAMMING.
2. Press # again and the display shows
OUTPUT 1.
3. Press A or B to select the desired output (1–4), then press #.
4. With the display showing
PARTITION ASSIGN 1, press 1 or 2 to select the desired partition.
Press # to confirm the partition.
5. Press A or B until the display shows
CONFIGURATION tttrr (current setting).
6. Enter the desired 5-digit configuration number for this relay. Press # to confirm the setting.
7. Press # and repeat steps 3 through 6 until all outputs are programmed.
Output Text (Acc. Modules—SnapCards—Output Text)
(10110—output 1, 10111—output 2, 10112—output 3, 10113—output 4)
(Default = none) Entering text for an output allows the user to control it directly or by schedule.
Use the following guidelines to “name” SnapCard outputs:
• Use the item numbers that appear in “Appendix B, Table B2” for characters and words listed
there.
Note
If you desire an output for
User Output Control you
must use the Output Text
feature to name the output. If
no Output Text is pro-
grammed, the user will not
have access to the output.
• If a desired word does not appear in Table B2, create it using the characters (custom text).
• When using words from Table B2, spaces between them appear automatically. When using
characters from Table B2 to create words, you must reserve an item number for a ‘space’
after the word.
• Each character or word uses up one item number. For example, a word from the list counts
as one item number. A created word (such as BOY’S) counts as six item numbers—4 letters,
1 apostrophe, and 1 space.
• Only 16 item numbers are allowed for each output name, so plan ahead before programming
output text. You may need to abbreviate words to avoid running out of item numbers.
¾
To program Output Text:
1. With the display showing SNAPCARDS, press #, then A or B until the display shows OUTPUT
TEXT
.
2. Press # and the display shows
OUTPUT 1.
3. Press A or B until the desired output number is displayed.
4. Press # and the display shows: OUTPUT N ITEM 0 0 - ..Where ITEM 0 is the first character/word
location and
0 is the character/word number.
5. Enter the number of the desired character or word, or scroll through the numbers by pressing B
(forward) or A (backward). If you make a mistake, simply enter the correct number or continue
scrolling through choices.